ArmorSuit 6 Pack for Apple Watch 42mm (Series 3/2/1 Compatible) Screen Protector MilitaryShield HD Clear TPU Film - Made in USA

When it comes down to finding the right protection for my watch, ArmorSuit MilitaryShield is my go to brand. Why? Not only are their screen protectors durable and reliable, they also offer some of the best protection for any type of device you have. For the Apple Watch in particular, their screen protector leaves your whole display covered from edge to edge. Their screen protector is designed so that every part of your watch gets the protection that it deserves. Wet application can be a tad bit tedious, but the results are definitely worth the time invested into it. Installing the screen protector on a watch that has curved edges could prove to be a little tricky. The key to applying the protector on perfectly is getting the flat surface to stick onto the watch first. Once that is done, I waited for about 15 minutes for the edges to get tacky. Once they are tacky, then I would press the edges down with my fingers. I remembered to spray my hands with solution before doing this, and found that it really helped in applying the screen protector successfully. I realized that using too much solution will not help the edges stick, so this was the best solution that worked for me. They recommend allowing the protector to dry overnight, which is exactly what I did. However, I was still extra careful with it the first couple of days just as an extra pre-caution because I didn’t want my newly installed protector to come off so easily. Afterwards my screen protector dried clear and it was almost like there was nothing on my watch! It is truly invisible. I am very grateful to have stumbled upon this product, and will continue to use this brand for any future protection I may need for my devices.

So a lot of reviews complain about the application process which can be a bit involved I agree so here is what I learned. Use a space heater to gently warm up the film while you use the rubber thing to smooth in place. I waved it in front of the heater for a couple of seconds after I got most of the liquid out. I stole the heater tip from a YouTube review. They used a hair dryer but I am not dexterous enough to hold a hair dryer and maneuver the watch. A review here said to watch pressing your nail into the film during the application process. This is a Pro-tip! I failed at this and have a small indent in my screen. I barely notice it but it is there. So once you get past the application process it’s great! There is a small gap around the perimeter of the watch. So it does not cover from edge to edge, which I am ok with. The gap hasn’t seemed to hinder the protection of my watch at all and I do bump and knock it a bunch. You can fill the ridge of the protector, but I have mine for several weeks and the edge hasn’t lifted or rolled yet. It’s perfectly clear so while looking at the watch I can barely notice it is there. I can however feel the difference. It’s not that smooth glass like finish that feels so nice. This is a replacement for a screen protector that had a bumper that 1. Had a gap. 2. There was a space between the bumper and the watch were dirt could get in and did and lastly broke within a few days of wear. Bottom line, the watch looks beautiful without the screen protector and while I may not scratch or damage the face of my watch without a protector I feel better knowing it is there. So I sacrifice a tiny bit of beauty for a large amount of protection. Like using a condom, doesn’t feel as good or look as nice but the protection is so worth the sacrifice! I will update if/when it fails.

This screen protector was very disappointing. The functionality is lacking because it does not stay properly adhered, which makes it unreliable as actual screen protection. Cleaning the screen and the protector is easy enough, but that does not help when the protector will not lay flat or stay in place. The fit is off, with edges that do not align correctly with the Apple Watch screen and begin lifting shortly after application. Touch sensitivity was noticeably affected once applied. The screen felt less responsive, and taps and swipes did not register as smoothly as they should. That alone makes daily use frustrating. As far as screen protection goes, it does not inspire confidence. The material feels thin and cheap, and it started showing wear very quickly. Even though it comes in a multi pack, the value for money is not there when none of them perform well. Overall, this product did not work as intended and was not worth purchasing.

Update: 7/25...so after repeated changing of cases the edges of the screen guard did come off a bit and gradually got some dust stuck on it. So i removed the case and placed the second screenguard in the package. I still like and now im using my watch case free. I will try another case which maybe stays a bit on the outside and doesn't push off the screen guard. We will see. If not, ill just stay caseless as it looms better that way anyway. But no issues with the screen guard surface tho, handles bumps and minor scratches like a champ but I'm pretty careful with the watch anyway. Still highly recommended and the best in the market! I recently bought an aluminum 42 mm apple watch and immediately saw videos showing how easily it can get scratched. I started looking for tempered glass optiona but because of the curves edges none of them gave full coverage. So i compromised on this one. But i gotta say, i am very happy with it so far. The order included two protectors, a squeegee, a microfiber cloth, and liquid spray for wet install and instruction pamhplets. The protectors are made to perfectly fit onto the watch and doesn't leave any spot uncovered on the screen including the edges. The installation is not difficult but you have to be sure to follow the instructions properly. It took me abt 15 mins. Watch the video tutorial in the link they provide. It is a wet installation and you should allow it some hours to sit after you place the protector so it stays put. You can't even tell that the protector is on the watch unless you pull the watch right upto your eyes which is great! If you install it properly you will NOT get any bubbles, and even if you do most will disappear in a few days. If they don't this protector is easily reinstallable with the fluid adhesive spray provided. DO FOLLOW THE INSTRUCTIONS TO THE LETTER! An important note for people using apple watch CASES, let the screen protector stay on for a few days before attempting to put cases on the watch. I read a lot of complaints from other buyers saying the case pulled out the screen protector. So I decided to wait some days after installing the protector before putting on the case. And the protector is holding up fine. I do take care a bit while pulling out the case, and on occasion it has slightly pushed the protector off but it is hardly noticeable and easily stays on after pushing it down. There are very few dust particles set on the edges but they are on the outside of the edges, not under the protector, so you can wipe them off easily. As far as scratching goes, i haven't had any scratches so far but I haven't really banged it or dropped as i am pretty careful with watches in anycase. There was a very minor scratch once and the self healing tech seemed to work fine and it has disappeared now. If any major scratches occur, i will update this review to see how the protector handles it. Overall, i am certain this is the best screen protector available for the apple watch right now. Unless they can build a tempered screen glass protector with full coverage that stays put around the edges, this is the BEST bet you have. So buy it now!

This is very good product but it requires some care when installing. Unlike most screen protectors, the adhesive is activated by spraying. This spray helps reduce fingerprints and eliminates bubbles when installed properly. It also complicates the installation as the protector will slide easily. Some tips: 1. Don't overspray. Just mist the protector. 2. It will be very slippery. As another reviewer suggested, apply to the flat top of the watch and let it sit for at least 10 minutes. Then, hold one side with your finger and gently use the squeegee to work from center to around the curved surface. I had to gently work the edge around the curved surface a few dozen times to get it to remain down. Then work the opposite side and finally, the other 2 side. I keep a cloth in case any liquid is squeezed out but if you were careful not to over-spray, you should be good. As it dries a bit more, watch the edges and gently smooth if you need but you shouldn't need to do this after another 20 minutes or so as the adhesive will be drying now. You have to look very close at my watch to even tell there is a screen protector on it. The package came with 2 protectors. I'm not sure if the intention was to install one on the back but I have only used 1 right now. If I were to make one product improvement, it would be to have it wrap the sides so they don't get scratched, but it would probably be very difficult to do this and not end up with wrinkles on the corners.

I enjoyed this screen protector a lot, for the whole 3 days I had it on my watch. Application is very simple and it fits really well, almost like nothing is even there. At first there is some "smearing" underneath the protector just because the solution hasn't fully dried yet. But that goes away in a few days. (The only reason I know this is because my girlfriend has one on her watch still that hasn't been damaged, and it looks awesome.) The issue I'm having is that whenever I put it on, just a few days later the screen was severely scuffed and had a big white scratch on it. It was probably my fault but that wasn't the only problem. Their policy indicates that they will replace any screen protector for a $1.99 S+H fee, which is an awesome deal if you ask me. However... I emailed them and never got a response. This was about a month ago if I remember correctly. I don't even have the old protector now, and the website says you have to send in the protector or take a picture of it (which I did). I'm not sure what is going on and I'd love to use one of these protectors again but I'm not buying a brand new pack of them when they claim to have a lifetime warranty. Overall, good quality item. Bad customer service.

It's dirt cheap and works great. Pros: - Unlike a lot of screen protectors, this one causes minimal/no "rainbowing" of the images on the display. - The wet install was relatively easy to do on such a small device. Easy to accomplish if you close the bathroom door, switch the shower on max heat and flow, and then install - this way all the dust in the room sinks to the floor. - This protector covers the rounded edges of the watch, not just the flat top. - Nobody has ever once noticed that my watch has this screen protector installed. They all commented on how clean my screen was, though! - Buy one box, comes with 2! (Had to replace mine once... See below) Cons (minor things): - This is a weird one, but spray sunscreen DESTROYS this screen protector. I don't know what chemical reaction occurs but it warps and "melts" the screen protector on contact. Figured it couldn't be healthy to have whatever chemical reaction happening so close to my skin so I replaced the screen protector with the SECOND one included in the box. - When your watch reflects direct bright light, you can tell that there is a bit of an "orange peel" texture on the surface. However, you won't feel it at all when glossing your finger over the screen. - Now that the Apple Watch has some stuff rolling out in watchOS 3 involving handwriting text on-screen to respond to texts and emails, know that this screen protector is stickier to the touch than the bare glass. This makes writing a little awkward, like dragging a pen over the skin of an orange.

ArmorSuit MilitaryShield really strives to make sure that your device is protected from edge to edge, leaving as little of the front surface of the glass display vulnerable to opposing forces that could cause damage. My purchase of the Apple Watch is an extremely valuable one and I wanted to be sure that it is completely protected. So I purchased their shield because it covers the WHOLE glass display, including the curved edges. While applying the screen protector onto the device, I noticed that if the edges are too wet, they will not stick to the curved edges of the display. So the following was done in order to have a successful application. First, after I sprayed both sides of the screen protector and my fingers, I applied the screen protector onto the watch’s flat surface and make sure the protector is sitting on a right position. Secondly, I allowed the screen protector to sit on the device for about 5-10 minutes in order to allow the edges to get “tacky.” After this short waiting period, I pressed one side down making sure that it aligns perfectly to the edge. The same was then done for the side of the watch that was perpendicular to the side that was originally pressed down. I noticed that my screen was slightly off alignment, but it was still wet enough for me to slide it across the surface to fix it or you can just lift it back up and do step one again until u like it. After fixing the alignment, I proceeded with the remaining two edges. Once the screen has completely dried, it looked crystal clear. It looked like there was nothing on the device at all! When it comes to protecting my devices, I will always choose ArmorSuit.

Really happy with these screen protectors, much better than the tempered glass ones we’ve used previously. Easy to fit if you’re patient and follow the instructions. Have lasted well so far (4 weeks). Feels good on the watch and is invisible.

fits like a charm..only if you follows the instructions.

Following the video, goes on easy and looks good when it’s on. The cover wraps the around the screen curve. Problem is that it started pealing at the corner after a few days. Ended up having to replace the first cover with the spare. The new cover lasted about a week, then it started peeling on the side (not the corner this time). I reapplied the spray liquid and then used a dryer to push the protector back into place. This worked for about another week. The cover then started lifting at both the corner and the side. Vendor was good, sent a replacement kit, but I would not recommend the product. Frustrating to have to reapply covers every week (my last cover lasted over a year, I replaced it because of a light scratch).

Great protection for my watch

Protects well initially... but despite following instructions to the T... corners NEVER stay on properly and after a few weeks are collecting all kinds of grime and dirt. Having to remove prematurely to protect watch from getting scratched.