WOWOONE CNC 3D Printer Kit for Arduino Mega 2560 R3 RAMPS 1.4 Controller LCD 2004 + 6X Limit Switch Endstop 5 A4988 Stepper Driver 3D Printerarduino arduino
Description
- 3D Printer Accessories Set meets most needs. Including CNC Shield V3.0, UNO R3 Board, A4988 StepStick Stepper Motor Module. The 3D printer stepper motor shield V3 can be used as driver expansion board for engraving machines and 3D printers. It has in total 4 channel slots for A4988 stepper motor driver modules for driving 4 channel of stepper motors. Each channel of stepper motor only needs 2 IO ports, which means 8 IO ports is sufficient to manage 3 stepper motors This shield can make quick work for managing stepper motors in your project
CNC Shield Board: 1>PWM Spindle and direction pins 2>4-Axis support (X, Y, Z , A-Can duplicate X,Y,Z or do a full 4th axis with custom firmware using pins D12 and D13) 3>2 x End stops for each axis (6 in total) 4>Coolant enable 5>Uses removable A4988 or DRV8825 compatible stepper drivers 6>Compact design 7>Stepper Motors can be connected with 4 pin molex connectors or soldered in place 8>Please note that this is an unassembled kit and Basic soldering skills are needed A4988 Stepper Motor Driver: 1>Low RDS (On) Output 2>Automatic current decay mode detection / selection 3>Mix with slow current decay modes 4>Synchronous rectification for low power dissipation 5>Internal UVLO 6>Crossover-current protection 7>3.3 and 5 V compatible logic supply 8>Thermal shutdown circuitry 9>Ground fault protection 10>Load short-circuit protection 11>Five selectable step modes: full, 1/2, 1/4, 1/8 and 1/16 UNO R3 Board for Arduino: 1>MCU: ATmega328 2>USB interface: ATmega16U2 3>Operating voltage: 5V 4>Digital I/O pins: 14 (including 6 with PWM capability) 5>Analog input pins: 6 6>I-I/O pin output current: 40mA max 7>3.3V output current: 150mA max 8>Flash memory: 32kB (0.5kB used by bootloader- included) 9>Static RAM (SRAM): 2kB 10>EEPROM: 1kB 11>Clock speed: 16MHz LCD 2004 Smart Controller Easy connect it to your Ramps board using the "smart adapter" included. After connecting this panel to your Ramps you don't need your pc any more, the Smart Controller supplies power for your SD card. Further more actions like calibration, axes movements can be done by adjusting the rotary encoder on the Smart Control panel.
Reviews
D**U
Mega 2560 worked for me
I didn't notice all the one start review when I placed the order. So when I started trying the board after reading all those reviews, I really worried. On the first try, I could not download a test program from Arduino IDE either. I went to Tools->Port and selected the serial port, still didn't work. Then I went to Tools->Board and found Uno board is by default selected. I changed the board to Arduino Mega or Mega 2560, then I could download program successfully. I only tested the blink program with different delays. Will update if I find something not working
G**8
Arduino usb port was flakey just reflowed the solder points
After seeing the reviews on this I was prepared for a doa arduiono but I mostly just wanted the ramps board drivers and lcd screen so purchased it anyway. The packaging was above what I expected all parts were individualy wrapped and it came in a nice reausable case and yes my arduiono was doa. It failed halfway thru the first flash then the pc didn't recognize it at all. I was able to flash it using another arduiono ao I figured it's the usb port so I reflowed the solder on it and now it works. I probably won't use this arduiono on my project but all the other parts worked fine out of the box.
J**D
Not working....
Not working. Shows up as a device, everything lights up and no noticeable defects... can’t get anything working through the arduino program on PC... still trying, will be sending back if unable to resolve within a few days.
J**S
A good product
ANY instructions would have been useful it came with absolutely zero instructions at all. Setup was rather difficult but the printer is working now thanks to YOUTUBE. EDIT less than 1 week and the FAKE arduino has failed
D**A
Bootlegged Arduino Mega Board
I would rate this 0 stars. Bootlegged Arduino Mega 2560 board. My laptop didn't recomend the arduino mega. I couldn't even upload the mega driver to the board. The Ramp 1.4V board was dirty with flux. Not pleased with this product at all. I decided to buy the name brand board.
P**5
Died shortly after use
Firstly, the drivers never were able to microstep the motors, which reduced the resolution by 16x and a couple of weeks after using it, it just straight up died
K**S
nothing is put togeather at all
I did not like that it was nothing at all was put togeather
A**R
Dont purchase
Mega 2560 stopped taking uploads. Solder connection on usb port was shorted when I first got it. I would not purchase again
Common Questions
Trustpilot
1 month ago
3 weeks ago
