DOQAUS Ice Cube Tray with Lids - 4 Pack Stackable Silicone Ice Trays for Freezer, BPA & LFGB Safe, Easy Release for Kitchen, RV, Cocktail, Coffee, Soup & Food

Nice Ice Cube trays. The silicone bottom makes it easy to remove the cubes. I uses these for other than ice cubes - like broth that I can freeze in smaller amounts and with the lids make easier to store

Love them! Perfect for what I needed. I usually have limited room in my freezer and these are small enough and stack nicely and do not need too much room. So easy to pop the cubes out once frozen. Great product.

I love these ice cube trays! I even ordered a second set. The lids work perfectly to stack them and they’re small enough to twist and the ice pops right out!

I do love these trays and they work very well. The lids are an excellent feature for stacking them. They fit nicely in the freezer. The ice capacity is normal. It's easy to remove, just trust and bend a little to get them out. One of mine did crack in the corner, but it's still very much usable.

About 8 months ago my refrigerator ice maker was having problems. The frig. was quite high quality, but not it's ice maker, since the freezer temperature is controlled by the freezing compartments that are in the lower half of the frig., while the upper half, is for standard food & fluids, which is always set below freezing. However, the upper part of the frig., unfortunately also contains the "ice receptacle maker" which also delivers the cubes on demand. The freezing air it needs is blown into the upper frig. compartment ice maker from a freezing compartment in its lower half. After some 6 years of use, the frig. ice maker was giving me problems, since lower temperature, humid air was leaking into this compartment from the less than perfectly designed, silicone rubber side walls, that leads to much ice forming in the ice maker freezing component itself. I tried to fix this problem, but eventually the ice maker no longer made ice cubes. However, the dispenser tray still worked perfectly well- it just needed ice cubes. Voila! I found that I could fill the working frig. dispenser tray with ice cubes, made first, in an area of the lower freezer compartment. At first, I purchased an ice cube making tray set that could make up to about 70 smallish ice cubes, but they were difficult to get out of their single tray, due to the fact, that the entire ice maker tray was made of solid plastic, and some to many of the ice-cubes were difficult to release easily. So, I went back to Amazon & found another ice cube tray maker, that many readers were quite happy with. So about 6 months ago I purchased the above 4 tray set that is being reviewed herein. It turned out that this set is superbly designed, very easy to use, still functions 100% well, with no breakage of any plastic parts (but I do handle the parts. particularly the thin tray covers with care). Each single tray (of 4 such trays) makes 14 medium sized ice cubes x4 trays overall = 56 cubes in total. It takes about 800 cc to fill the 4 empty trays. What is so superb about these trays, is if you use them correctly, the ice-cubes are very, very easy to remove quickly. To re-fill them again with water for refreezing, takes only a couple of minutes. Their most important component of this ice making tray, is that the bottom of each cube compartment, is made of soft & pliable silicone rubber. Now, this is how I suggest using this set to optimize their function: 1) remove the trays from the frig. freezer compartment and bring them close to the kitchen sink; 2) then run for 2-3 seconds some hot water over the cover of the first tray; 3) then turn over to its bottom silicone side and run some hot water over the entire silicone area of 14 cubes; 4) then place the tray over a large enough receptacle (about 12x8"x2" in size) & twist the tray slightly to at most moderately, after which most, if not all, the cubes will fall into the receptacle; 5) turn over the tray, and if any cubes are left, simply push with a finger on the silicone rubber base to dislodge the remaining cube(s); 6) repeat this procedure for the remaining trays that you decide to use (my needs are for only 3 trays at a time, not four, since my frig. tray only holds 3 trays of cubes before over-fill); 7) next, put the ice cubes into the Frig. ice holder bin and place it back into its frig. bin compartment ASAP, to minimize ice cube melting; 8) refill your empty ice trays with your liquid of choice-- typically plain water. One last item-- The refilling of the trays with water. For this, I found an excellent item from from the "JOIE" Company, which is a 500 cc red & clear measuring cup (with cc and oz markings) that dispenses the water into the trays cube-slots easily and quickly. Fill each cube space to within 1-2 mm from the top of the tray to compensate for expansion of the volume of water after freezing. Hope you will enjoy using these excellently designed & practical ice tray makers, as much as I have, with several months of continuous use, without any damage to date.

They break easy when taking the ice out of it.

Love the smaller size. Works well for my freezer. Love the lids so they stack with no mess. Easy pop out helps my arthritic hands. Great purchase

These ice cube trays are ok. They came with one of the lids cracked, which I was not impressed with, but I did not want to send all 4 sets back for that 1, it works ok the way it is. Because the lids are hard plastic, it makes them very fragile when cold and it is tough to get them off, so another since then has cracked, but is still usable. The ice cubes are easier to get out than from plastic ice cube trays, so I do like that about them. I bought the 4 set because I drink a lot of iced water, this way I am only filling every 2-3 days instead of every day. So it is plenty for me.