uxcell Foam Tubing for Handle Grip Support, Pipe Insulation, 25mm(1") ID 35mm OD 1m Length Black

I purchased this to replace the foam padding on the handle of my rake. This padding was a little bit larger than the handle so it is a little loose, but it manages to stay in place when I grip it and it gets the job done (keeping my hands from blistering when I rake). Very pleased with the padding it provides.

Used as replacement cover for the step up on my jet ski. Worked perfectly. Cheap, looks good and effective.

They worked Perfectly for the handles on my zero turn mower.

I've found that this is the very best foam to use on your bicycle handlebars. It's not too thick and has sufficient padding. I wrapped the foam with a cloth electrical tape and the final result looks great and feels great. Measure the OD of your handlebars to order the right ID of the foam. A little talcum powder put into the foam will allow it to slide onto your handlebar easily. For covering the top sections of your handlebars (use an xacto knife or razor blade) CAREFULLY slice through side of the running length of the foam and then position that cut underneath the bar. Once you tape over the foam pieces, all will be great and you will be surprised what a great final product you have. Your bike and your hands will love you. This is WAY more effective than simply buying foam insulation for piping. That foam doesn't have the consistency of this foam. This is the excellent tape I used to wrap over this excellent foam - it's also on Amazon: https://a.co/d/0Wudzfj

Just what I was looking for.

This tubing insulation is just what I needed to give new life to my tripod. The foam pipe insulation I had around it before was starting to disintegrate and was looking shabby. This foam tubing isn't like the foam insulation for water pipes. It's more like neoprene material, except without the outer fabric layer. It really does insulate (more on that later) and provides a nice grippy surface to hold onto. The only problem is the way it is folded, presumably for shipping. The tubing was shipped in a plastic envelope and was folded twice leaving three creases. These creases are permanent and unsightly. It ruins an otherwise beautiful covering. I tried using the same methods of removing creases from neoprene—pouring boiling water over the creases and inside the tube. Even with boiling water inside the tube, I could comfortably hold the outside of the tube, verifying the insulation performance. While the boiling water relaxed some of the smaller creases, the deep creases stayed. Even after letting it sit for 24 hours, the creases remain. A note on installing. These tubes are bit snug to keep them in place. This tube's ID is 28mm. My tripod leg is 28.1mm. The tubing will stretch a little, maybe ±1mm. Carefully measure the round part where you plan to install this, preferably with calipers. To install them, DO NOT USE any sort of petroleum lubricant such as WD-40 or grease. The tubing will slip and not stay in place if you do. To help slide it onto whatever you're mounting this on, use 91% rubbing (isopropyl) alcohol. DO NOT USE ethyl alcohol. Clean the surface where it will go with the alcohol, then pour some inside the tube and swish it around. While it's still wet slip the tube onto the surface. The alcohol gives just enough lubrication to allow the tube to slip. If tube starts to stick, lift up an edge and pour a little bit more alcohol inside. The alcohol will eventually evaporate and the tubing will stick to the surface and stay in place. For the product, I give it 5-stars. For how they store and ship it, I give them 1-star, so overall, 3-stars.

Works great to insulate the low side line under the hood of my 2011 F-150. This insulation fit perfectly and only needed to be slit on one side to slide over the low pressure line. These trucks are notorious for ac not blowing very cold. Was able to buy me another few degrees of coldness in the cabin. Secure the wrap with plastic zip ties and you’re good to go. Properly charged and with that long line under the hood insulated, I get down to around 42 degrees of cold on an 80 something degree day. I’m good with that.

I thought you could just wrap it around the handle but no you have to take the handle off blah blah blah 😭😞 so ....

I'm using this tube for lanyards which is soft on the back of the neck

The tubing was great quality product to replace the outside exposed refrig lines running from my air con

I bought this to pad the neck holder of my guitar rack (Hercules Stands GS523B) ... fit snug (used some light oil to slide it on) and does the trick :)

The originals tore on my Elliptical, found them and they are a great replacement fit

My trailer hand rail was deteriorating due to the sun and with this replacement we got brand new look and much much better grip