Moen Chateau Chrome One-Handle Low-Arc Kitchen Sink Faucet with Side Sprayer, 4 Hole Kitchen Faucet, Separate Flexible Pull Out Spray Head, for Commercial, Laundry, Utility, 7430

Good quality item. Came with easy to follow instructions. Works well; moves smoothly from side to side; spray attachment works well.

I purchased this faucet to replace an old leaking/corroded kitchen faucet. The installation was easy enough and took approximately 1 hour, which included installing new compression fitting shutoff valves. I am not a plumber by trade. The item was shipped promptly and the faucet is solid, works well and looks great. The supply lines are part of the faucet and are plenty long enough to reach the floor. All of the lines go through only one hole, but still requires a 4-hole sink, which is fine because that is what I have. The steel plate uses the 2 outside holes to keep the faucet base from turning. After a week of good use, there are no leaks to report. My only, very minor, complaint is that the side sprayer is completely plastic.

Very happy to have purchased and installed a new Moen faucet (and great service and pricing on Amazon's part always). The faucet was relatively easy to install (save for the limited space under our sink to operate within...you may need to gather a pillow and be prepared to work like a contortionist :-)) and so far it's operation is flawless. The flexible hoses (vs copper hoses and connection of the older unity) are a big plus in my opinion as well. Overall, nice quality and a relatively easy install (~ 35 minutes)....a good value for the $$!

Fits nice, was easy to setup . I had a 3 hole.. difference from my stock was that this one all the fitting/extensions come out from the middle for your hot cold and extra spray, where my stock sink faucet the hot and cold came out or plug to each hole on left and right of faucet.. Only thing I didn’t like was that since all connections are in the center… if you got an old sink like mine.. and a bit warped already… as you tight they middle screw with all the connections, the left and right edge start to lift up and leave a gap where water can drip into and under the sink . Would have been nicer if the sides had at least a small simple bolt/ screw butterfly bolt etc to allow you to also tight torne the edges /corners of the medal plate that covers the other 2 sink holes . What I ended up having to do was tight the middle just right where left the smallest gap possible without warping the sides up, and then I literally loaded the entire edges around the metal plate with clear silicone.. almost not noticeable when dry, however if you take a close look around the edge of my faucet plate.. you can see the messy silicone I have there not pretty but only way I thought about to seal the sides and all around so water wouldn’t drip in

Updating the kitchen and was told by my plumber to get a MOEN. Boy, was he right! That old DELTA [https://www.amazon.com/Collins-Single-Handle-Kitchen-Matching-440-WH-DST/dp/B002LKU4VC/ref=sr_1_2?crid=EK6N9DGEY5L9&keywords=delta%2Bfaucet%2Bwith%2Bspray%2Bin%2Bwhite&qid=1702094004&sprefix=delta%2Bfaucet%2Bwith%2Bspray%2Bin%2Bwhite%2Caps%2C256&sr=8-2&th=1} after just 5 years was so difficult to use the handle. The top of the faucet got dinged so easy, because of the very light construction of the whole unit. It would actually rock the base plate and you were unsure whether of not it was going to bend in half. The MOEN is so much more sturdy; the handle and the faucet itself are silky smooth to move left and right and forwards and backwards. The base plate is veeery durable and stable. My only knock is that the sprayer is not "serrated" at the bottom [where it mounts to the sink] so it swivels all over; when you need to use it you have to pull it up and grab the sprayer in whatever position it is in, then point it in the direction you need it. The DELTA had grooves on the sprayed base, so that it was "at the ready" as soon as you needed it. Small kvetch! The DELTA is now $180+ and the MOEN is a bit over $100. The choice is so easy...

I like the way this faucet attached underneath the sink. Often we have to Dremel our old faucet off when installing a new faucet, but this faucet uses screws which will be easier to remove when the time comes for a new one. The only problem we had was settling the faucet into the metal plate. We watched a helpful video online and it said there is apparently a notch somewhere and to twist it a little until the faucet settles into place. Unfortunately the directions said nothing about this. But other than that, we are very pleased with this faucet.

Worked great, same model that I am replacing, everything fit as it should.

look great good price easy to install

Happy with the quality of the faucet. I can’t speak to the easy of installation, but after several months it works like a charm. Although the sprayer feels cheap, it does the job and I like having the option. It replaced a similar set.

Easy to install, looks great. Turns off completely - no lingering drip or two like old faucet.

Super produit tel que commander

This faucet works fine. Installing it is a bit fiddly-- you have to reach up behind the sink and tighten three long phillips srews to hold the faucet down. The main criticism is that the flow rate is lower than expected, lower than my previous Moen faucet, and lower than the spray attachment. The best way to fill a larger receptacle is to use the spray attachment, the faucet itself. (This tells you that they have somehow purposely put in a flow restrictor into the faucet itself) takes significantly longer to fill the pot.

worked very well