9 PCS Concrete Stone Wall Molds – Reusable ABS Forms for DIY Panels W02

These things are awesome! I made ~100 stones and they are still in great shape. I used baby oil for the release agent. I built a shake table to minimize bubbles in the cement which worked far better that trying to manually shake them out. I used a heat gun on low careful not to distort the mold to help with getting the mold to let go of the stone. Clean the cured cement left behind right away after dropping the stones and you will have a much easier time than if you wait for when you need to pour again. Also, I used a piece of scrap wood to scrape the cement residue and did not scratch the molds.

I LOVE THIS MOLD!!! I have read most of the results before and after purchasing. So to the point. Patience!!- don’t believe too quick to remove from mold. The cement used is most impossible as they tend to break a lot. It was after my 4th set that I got results. Issues were below; 1. Was only using sand and cement and was mixing ratio 3sand:1cement( this was TOO WEAK) - when I use more cement it dries faster. 2. I did not give it enough time to dry. takes about 12-16 hours to safely remove castings from molds. Another issue was that some of the molds are warped, hogging( middle section pushing up). I solved the issue by resting them on chocks at each end so the weight of the concrete presses down the middle by gravity. This works well!! Also, I used a vibrating table. When they break, if you look closely at the inside lattice( surface) you will see a lot of air pockets. So the vibrating table eliminated that. I find that cooking oil is a bit too thin and leaves a lot of bubbles even with the vibrating table. A thicker substitute worked for me( 20W40) motor oil. For a clean professional finish, when I LIGHTLY oiled the molds, right before I pour the concrete, I lightly pour powdered cement to coat the surface, as you would do when baking with flour in the baking trays. I find the finish is VERY smooth and even if bubbles were there before, this would eliminate them. ENSURE the concrete is mixed thoroughly, using sand, fine gravel and cement. My mixture 3sand:2gravel:2cement. This is so because I don’t have “fast setting concrete”( Quickcrete). I researched the components and tested my method. I used ordinary cement. DO NOT FORCE THE MOLDS OFF. If when you are removing them and they are tight, gently pour warm water over the mold and they will come off easily, but try not to do this as much it may eventually warp the molds. I colored the concrete mixture but find staining them works for me. It’s a very patient hobby. You will get the hang of it after a couple tries, just don’t give up!!. Great stuff and good luck!!

This product is sturdy and will stand the test of time if cared for properly. The end product looks amazing. The large molds are somewhat thin in the middle creating broken tiles. To solve this issue I used two layers of hardware cloth cut just slightly smaller in length and width. Pour half way up with your concrete add hardware cloth and finish filling the mold. Always tip your tile on its side lengthwise before picking it up (while still curing) and you won't accidentally break a tile in half. I'm using canola oil as the release agent brushed on with a paint brush. Its a chore to make only 9 per day, I'll likely buy another set. I highly recommend this product.

This is a very time consuming but money saving way to get the custom look you want. I only bought the 9 pce set. In hind sight i should have bought the full package. Out of the 9 there was one no matter what i did it would break. But really its no big deal. Run the broke edges throigh your tile saw n now you just have two smaller pcs. Lol. Anyway to get the 200sq ft I needed in Washington starting in March with cold nights i could only get one mix in 24 hrs. Once June came round i had a system and with warmer days n using the red bag quick dry cement i was getting 2 mixes in 24 hrs. My best results. 1. Every use....... Clean thoroughly (dry wipe) 2. Murphy's oil in a spray bottle then use a paint brush to coat EVERY part including tight corners and sides of mold. No puddles. Dont worry if it discolors your mix. It washes off. 3 red bag qick set concret. 1 bag plus 2qts portland cement 2qts sand 1 qt pea gravel. It fills all nine every time with nothin but a handful or so to toss. 4. IMPORTANT. You need a makeshift vibration system to get out air bubbles. I attched my bench grinder cause it shakes a lot to a board under shelf across a couple saw horses. Ran for about 10 minutes. This is where practice never makes perfect but you will get better at it. Removal. Dont twist. Dont pry from middle. Gently lay on face flat ...tap the corners. Lift. Slowly at a coerner or end pulling on lip. Carefully while softly pushing on the corner bottom. Then work other end. When you feel it move try n lift the entire mold straight up with a mild. Side to side rocking motion. They break. They break they break. Get used to it. Some molds never but 50% success is good. Like is said none of it goes to waste reall. Cut the broken edges off with your tile saw. Good to go. 4 1/2 months to make 200sq ft. Cost less than. $650 total. Find 200 sq ft of stacking stone anywhere for less than 3x that n you got a steal. Use acid stain. Idc about what any one tries to tell you. Use acid stain. Pick from 50 labels n 100s of colors. I did 2 coats stain n one coat clear gloss sealer. Added 30k to the street value of my house for under $1000. Just a lot of time.

Not good , to thin

Works great, but I found brushing in liberal amounts of vegetable oil works best as a mold release. They slide right out, and any excess coats the sidewalks when concrete inserted. Also veggie oil helps clean the residue for next round of brick making. Ready to remove in around 24 hours... reduces breaks drastically. 9 molds used approximated 3/4 bag of 80 lb concrete bag. I add stain to. Oncrete mix, and black stain to mold just prior to pouring concrete.... awesome results. I’m ordering more molds next month! Easy to use after short learning curve

good customer service and return service was awesome product was not what I needed and liked do to the molding not shaping correctly and was not what I expected ordered rubber wax molding it was awesome an easy to use and outlined everything on the molding when it was dry but over all customer service an policy was awesome

We used this to create stone for our siding and it worked great! We played around with sprays like WD-40, pan spray and cleaner spray to see which one helped the concrete not stick to it. We liked the DW-40 the best.

Gerade eben aus der Gießform rausgehollt, siet Super aus

Les Moules sont de bonne qualité. Utilisez un béton plus liquide pour de meilleures résultats. Et pour faciliter le démoulage, pulvériser un aérosol de type WD40 dans le fond du moule avant de couler le béton dedans.

Conception de bonne qualité, la structure est détaillée. Il est important d huiler les moules au pinceau avec une huile végétale avant de mouler pour un démoulage aisé . Ensuite depose du mortier et le vibrer, j utilise une technique récupérée sur internet, à savoir poser le moule sur une plaque en bois et mettre en appui sur la plaque une perceuse en mode percussion, ce qui vibre et chasse les bulles d air, donnant une pièce plus solide. Ensuite laisser sécher 7 jours puis coller les pièces au mortier colle, on peut les peindre par la suite avec une peinture ton pierre ou autre. Rendement: 1sac et 1/2 de mortier pour un peu plus d 1 m2 soit 6 euros du m2 pour un excellent résultat.

Le stampe sono di una qualità superiore faccile da utilizare e il risultato è ottimo

Ottimo prodotto e arrivato prima dell previsto