TruGlo Low-Profile All-Metal Construction Glo Dot II Universal Fiber Optic Sight for Plain Barrel Shotgun, 12 & 20 Ga/.410 Ga, Green/Red

Bought this for my Rossi Poly 20 GA. Really easy to install. Snap it on the barrel and it actually fits really tight! I ended with a sore finger tip when I had to peel it off the barrel because I had it ahead of the bead rather than behind it. I can definitely see better. A lot better in low light. Should be great for Dove or Deer.

I got this sight for an older, JC. Higgins, single shot .410 shotgun I've had for many years. It is a simple design with a bead sight. This sight is a great upgrade for the single bead and works great for most lighting conditions except very low light and darkness where it's the same as a bead sight. This is not a night sight, it is a fiber optic, but in daylight and room light this sight works really well. It's very bright. I would love to see TruGlo put this out with a TFO tube. It is easy to put on if you just read the instructions and follow it. Hold the sight over the barrel behind the front bead (meaning toward the breech end of the weapon. Place the end of the sight tube that is closer to the breech against the barrel and hold the sight at a 45 degree angle with the muzzle end of the sight barrel up. Then holding the breech end of the sight barrel against the weapon barrel push down and back on the front of the sight at a 45 degree angle until the back end of the sight barrel snaps over the weapon barrel; keep up pressure as you continue to press the front of the sight barrel back and down to get the rest of it around the weapon's barrel. Just make sure you don't press on the fiber optic tube itself. It will snap right into place. Lastly use a flat blade screwdriver to push the sight forward so the front notch is centered around and against the front bead, being careful not to scratch the weapon's barrel. You might have to rotate the sight barrel a little to straighten it out so the fiber optic tube lines up straight with the sight line of the weapon.

I had previously installed one of these on my Mossberg 500 12g and was pleased with the results. It does take a little trial and error to hold the sight at the right angle and push just right, but it doesn't take long to be agle to pop it in place. Because the diameter of the .410 is so much less than the 12g, it's trickier to get the walls to spread. I actually pushed at the wrong angle and accidentally bent one side, but I got a pair of needle nose pliers and bent it back enough to find the sweet spot to get it on. Whateveer that plastic is, is a miracle. I haven't had a chance to fire the gun yet and see if it truly holds its place, but once it's properly mounted, it fits so tightly, it doesn't seem like it will be going anywhere from the gun's recoil. UPDATE: I've fired the shotgun about half a dozen times now and I dont' see a hint of movement. The fiber optic bead is bright red in the daylight and about the same size as the factory bead. I am thoroughly pleased. One note: This sight is harder to put on a .410 barrel than a 12g, so pay close attention putting it on. The plastic is quite firm, but it's also unforgiving. Get it right the first time,

Got this for my new shotgun because it was not that expensive and the brass bead on my shotgun was plain. Simple to install and looks pretty cool, especially in daylight. It is a little hard to see the green dot in lower light conditions, but its not that bad. Worked well at the shooting range and it worked awesome when I went shooting out in the desert.

This is a crappy piece of plastic and do not buy it. Trying to install it on my 12 gauges snapped in half and ended up cutting my finger real bad! The seller needs to be reported to Amazon as a fraud seller

For the money, this thing is a great bargain. BUT: It is NOT, NO, NOT, all metal. It’s a high grade plastic and it seems to be very sturdy. I’m going to buy a few more to upgrade some of my shotguns. It beats the heck out of a silly little bead!

I didn't really have many aftermarket options for my 870 express tactical. The front bead is press-fit so that excluded any threaded replacements. This product was pretty inexpensive and decided to give it a shot, (no pun intended.) Since the product is designed for 20 gauge weapons as well, it had to open to accomidate the extra width of the 12ga barrel. It will fit, but it's tight and on there snugly once it's fitted. I forecast this will be good once I get to shooting but it's a pain in the butt when trying to get the thing centered on the gun. There is a small ramp before the bead on my gun so the v-notch on the product didn't help. Finally got it centered and on there after making sure I didn't trap any moisture beneath it with a little bit of CLP. CLP or not, I don't think this thing is going anywhere. Tight. Unless it flies off when I shoot, I say give it a try. Not the cleanest install but whatever. Got what I paid for. Bright as heck indoors and out.

I picked up a Yildiz TK-36 single shot .410 at Academy. At $130 I couldn't pass it up. Best wood I've ever seen on a gun in at this price level. Got it home after work and tried it out. After about 10 shots I discovered that the front bead sight had fallen off, so I went to the internet to find a replacement. This Truglo sight looked like the most feasible option. I measured the barrel diameter at about 12.5 mm. Other reviews suggest this sight is intended to work with a barrel diameter between 11 mm and 15 mm so I ordered it. Being very careful not to damage the light pipe I wasn't able to snap it on as instructed, but since I'd lost the bead I was able to just slide it on from the end of the barrel. I ordered the red version and it is a clear bright bead that is far superior to the original bead sight. I'm very pleased with this sight but I haven't tested how well it remains in place after shooting.

for hunting ruffed grouse is amazing. Fast accurate sighting in bush and low lighting. Highly recommend. All my shots are now right on target. Easy to install and a nice tight fit.

Perfetto per SXP cal.12,facile installazione.

Bei eine Flinte ohne Zielschiene oder Befestigungsmöglichkeiten für andere Zielmittel ist es ein sehr guter Behelf. Die erstaunliche Leuchtkraft erleichtert den schnellen Schuss beachtlich. Vielleicht sollte man das Teil später mir einem temperaturfesten 2k-Kleber dauerhaft fixieren.

Parfait, acquisition rapide même en condition de luminosité faible, fait mieux qu un grain d orge seul. Je recommande largement

Passend für Caliber 12/76