hunhun 10-Pack 3.3ft/1Meter U Shape LED Aluminum Channel System with Milky Cover, End Caps and Mounting Clips, Aluminum Profile for LED Strip Light Installations, Very Easy Installation

I used these channels for mounting LED lighting under my 5th wheel trailer. I used this channel and some VHB ( very high bond) 3/4 inch wide double sided tape by 3M to adhere the channel to the frame. I installed the lighting strips then the led tape strip inside the channel using a better grade 3M double sided tape on the LED strips then the China crap tape included on the strip. If the LED strips fall inside the channel, the heat from the LED will burn the translucent cover that snaps into the channel. I also used some 12 amp step down power supplies in plastic boxes under the trailer set at 11.5 volts dc so as not to overdrive the strips. Any alternator produces up to 14 volts dc to charge the batteries and the LED strips are rated at 12 volts dc. Wired directly to the trailer wiring will overdrive the LEDs leading to early failure of the LED strips. There is so much time involved in all this wiring and soldering and connecting wires and connectors and putting the wires in split loom before mounting and installing the LED channels and lenses that you don't want to redo again later because you didn't use an adjustable power supply. Do it right the first time! These channels finish the job amd make the LEDs look factory installed with translucent lenses. I like these kits. If I had to do over again, I wouldn't buy the 3.3 foot long channels. I would buy the 6.6 foot channels instead. They are less money, and cover more distance fast with fewer joints. I cut them as needed with a hand grinder and use a small file to clean up the ends. So end caps can be installed using clear silicone for water resistant installations.

This LED strip housing is an excellent solution for DIY lighting projects, designed to neatly conceal and protect LED strips while enhancing the overall lighting effect. The built-in diffuser helps distribute light evenly, creating a smooth and continuous illumination without the harsh “dot” appearance commonly seen with exposed LED strips. Made for easy installation, it is ideal for under-cabinet lighting, shelves, display cases, ceilings, workstations, closets, and decorative accent lighting. The durable housing not only improves the appearance of your LED setup but also provides added protection against dust and accidental damage, giving your project a clean, professional finish.

Really impressed with these channels, clean machining, nice plastic, easy to assemble, light weight, able to use 3m two-sided tape to mount, hod great. Everything fits together precisely and covers go in smooth and tight. not movement. All the parts need included. Would recommend and buy again. Nice aluminum feel to each channel.

Great product! Wish it had mounting holes already pre drilled… but, like the price… so I guess we will drill them.

Good straightened extrusions, well fitting diffusers with peel off installation scratch protector, well fitting end caps. The included metal mounting clips work much better for me than the plastic ones offered elsewhere. The included screws and plaster anchors.round out a complete kit. I used these with a PIR (passive IR) motion detector BQLZR DC 12V~24V 8A Automatic LED PIR Motion Sensor Switch Light Lighting Delay Time 10 Seconds for Staircase , a 12V UL listed supply LPV-60-12 Sealed Panel Mount LPV Series AC-DC 12-volt 5-Amp Power Supply with LED Driver and 3500K (neutral slightly warm) 3528 120 LEDs/meter LED strips LEDMO 2835 LED Strip,600 LEDS IP65 LED Strip Lights Warm White 3000K DC12V 15Lm/LED CRI80,Waterproof For Wet Location,3 Times Brightness Than SMD3528 LED Light Strip to update our closet lighting. I also installed a PWM dimmer, but it wasn't really needed. I put 1 strip across the ceiling at the door edge and another across the bottom of the shelf the closets are more than 1m wide so I used an elongated mounting clip at the joint to keep the channels aligned. Muzata Extension Connectors for U-Shape Aluminum LED Channel, The Aluminum Channels Can Be Connected Seamless For Longer Lighting Project,20PACK . The screws for use with the anchors are longer than desirable for the wood shelf, but the ones that came with the extensions were a good length. since I used 2 sets of 2 ordinary clips and 1 extension clip for each closet, 1 set into plaster and 1 set into wood, the screw use happened to match the provided screws, I cut the extrusions using a 10" sliding compound mitre saw with a non-ferrous metal blade. Concord Blades ACB1000T080HP 10-Inch 80 Teeth TCT Non-Ferrous Metal Saw Blade . I assemble the diffuser into the extrusion and wrap it with one turn of painter's tape or masking tape straddling the cut line . The tape provides a markable, removable surface and controls the tendency for the plastic to vibrate and chip. I use the saw as a chop saw, descending slowly into the work diffuser side up. The resulting cut line doesn't need the extensive clean up that would be needed if a wood blade is used. The tiny burr can be ignored or removed with a diamond nail file or miniature flat file Needle File Set (HIGHEST QUALITY 6 PIECE SET) Hardened Alloy Strength Steel - Mini Needle File Set Includes Flat, Flat Warding, Square, Triangular, Round, and Half-Round File. For those who don't have the tool, I tested making a cut with a razor saw Zona 35-550 Fine Razor Saw, 42 TPI, .010-Inch Kerf, Blade Length 6-1/2-Inch , Cut Depth 1-3/16-Inch , and its possible to get a good clean cut without undue effort. Neither a simple hack saw, back saw (mitre box), or carpenters saw will make a clean cut. If you happen to have an ingersol air powered (auto) body saw with a fine blade it will make a serviceable cut requiring minor cleanup with minimal effort, but a harbor freight air body saw has more blade wobble and will shatter the diffuser. I cut the LED strip and remove just enough of the silicone to access the solder pads and solder LED wire EvZ 20m 66ft 20awg Extension Cable Wire Cord for Led Strips Single Colour 3528 5050 directly onto the strip. but there are solderless connectors offered on Amazon.if you don't wish to solder.

Really like these for mounting led lights. Like this one better than some competitors. The competitors seen the same, except much shorter. The plastic covers really help make the led strips seem like a strip of light as opposed to a line of LEDs

Purchase this to mount on the underside of my new basement bar. LED strip fit perfectly all the way around. Lights are secure.

excellent . I had to buy this product in the past but were 8ft long , it was very expensive. great price on this

Très bon produit a part peu être les attache fourni, si vous n'utilisez pas les vis pour fixer les attaches vous aurez du mal a fixer correctement l aluminium , mais sinon très bon produit en très bon état a l'arrivée