Bike Axle CYSKY Quick Release Skewer Front Rear Bicycle Axle Wheel Hub Fit for Road Bike, Mountain Bike, MTB, BMX (1 Pair)

Bought these to convert the front wheel of my e-scooter (Hiboy VE1 Pro) to have a quick release so I could easily store it in the back of my car. Installation was easy. The scooter had sealed bearings, so some parts were not needed. The axle slipped in nicely. One caveat was that the scooters spacings were slightly different than a bike's so you'll need to buy some washers and mess around with the spacings to get the stock disk brakes to play nicely, but overall not too bad. Would prefer it to be ~1 mm longer, but then again the scooter is not quite standard (compared to bikes) and it is still usable. No comment on durability for now, but no problems after 2 miles on rough countryside roads. No comment on the longer rear axle since I was not planning on changing the rear wheel.

I was surprised they arrived undamaged, even the dust covers, because it had a flimsy padded envelope, nothing else, not a quick rap of bubble wrap to prevent the inevitable. Anyway, what a great little set. Not only did the work "perfectly", they also saved me further fork damage and perhaps injury. I couldn't get the front wheel to seat straight and lock down properly (and safely) after two tries I realized my forks had to be bent, and sure enough, the right fork had a slight kick back, but noticeable once you see it. So, they were easy to install and fit perfectly. I can't wait to fix my fork and get some miles on them and see how they survive. 10/10

This installed easily, though be sure to retain the bearings from your existing wheel to re-use (with ample application of axle grease). The biggest issue I encountered is the size of the axle. It is (I learned) 3/8", which was larger than the fork of the bike was made to accommodate, so I had to drill and file out the fork ends to get it to fit. Be aware of this possibility.

Great set of road bike axles for 100mm and 130mm wide axle dropouts. Installs in minutes, and fits great! I changed my solid axles to these quick release axles. Durable metallic finish! The skewers work great and hold the tires in place. Quickly remove and install your wheels with these skewers. Make sure these axles measurements fit your wheels hubs before ordering.

These are ok, just ok. The nuts the bearings ride on didn’t fit my wheel, but I was able to reuse the old ones. The finish quality isn’t great, rough edges, paint was scratched up. They weren’t packed well, just dumped in a plastic bag to rattle around. That said they seem to work fine (though I’ve not been on a trail yet…) and are cheap. Decent for my 90s store-brand MTB rebuild project. Nice to have QR wheels.

Highly recommend, worked perfect & easy to install. Fast ship, thanks!

If I could give a zero star review, this product would still fall far short of even that. From the moment I received the package and installed the axel on my bike, it immediately stripped several teeth from both the axel rod and the nuts. The loc nuts are so cheaply made that the bearing covers literally sheared off into my bike, completely freezing the entire back wheel. It's clearly made of scrap or trash aluminum, probably the same grade as used for foil, and is far more of a headache and sanity drain than taking it to an actual repair shop. Do yourself a favor and keep scrolling, you're not going to find anything of quality here.

I was recently given an indoor bike trainer. my bike only needed the right skewer to fit that stand. my SO's bike though would've needed a replacement wheel at (using VERY round numbers here) $50-100 for the upgrade. the swap wasn't too bad to do really and I rated the "easy to install" down one star based on some headache regarding the axle length. this could have been my own fault by not measuring properly. in any case, it did work. no instructions or paperwork were included and I would base this on a typical bike repair shop purchasing this for the same purpose versus.... me. the kit did work as expected with the sole issue being the axle length came up about 5MM too long. I'll need to do some creative trimming to make it proper. also, there was one more thing. the included dust shields for the bearings were preinstalled and one had a bit of a bend in it. not really a big issue for me.

Damage item not recommended

Funcionó bien al principio pero se dobló, no soy una persona delgada así que quizá funcione bien para menos de 100kg.

Purchased these Axle's of Amazon. Product is well designed, due to harsh riding the rear axle broke and had to switch to a hard axle, its been alright.

Recomendable

Absolutely terrible. Product arrived damaged in a few places, rendering the product unusable. Don't waste your time.