Simply 50139 J-B Weld PlasticBonder- Black,25 ml

This is great stuff, the tubes are great no mess just twist off the cap and squirt it out, due to the tube design the glue is not going off between uses, sets quickly in approx. 30mins but fully cured in 24hours, then its rock hard and does not budge, great for me for all the little fixes, handy to have a tube ready to go, I also use the JB marine weld. fully recommend.

It just works. Despite some reviews stating that it is "too wet" and wrongly criticising the incredibly simple cap, this stuff is easy to mix, easy to use (when applying a little common sense) and absolutely tough as old boots. Twist and pull off the cap to open the twin tube dispenser and give the tubes a few taps to make sure there's no air trapped in either, push the plunger to squeeze out the 2 components, ensuring that they come out in equal amounts, mix well and, unless you need a really liquid material, leave for around 5 minutes, possibly even a little longer if you're using it on a vertical surface, so that it thickens up a bit. Do make sure to replace the cap the right way round, though - quite easy to do, since the component liquids are black and white. Once applied, it sets in 20 to 30 minutes (rarely the 15 minutes stated on the packaging), so you will have time to shape and smooth it as it starts to cure and might need to hold, clamp or tape a joint in place for a while. Other than that, once it has fully cured (I ended up leaving it for 24 hours, just to make sure, as it was still soft enough to indent with a fingernail, even after a couple of hours) it is both sandable and any overspill can be cut off or shaped with a sharp blade. I can only guess that those who have said it "didn't set" hadn't taken care to make sure there were equal amounts of the two components before mixing, as it is much like any 2 pack type adhesive or filler - too little hardener/activator means the product won't cure and harden. Honestly, when mixed and applied correctly, this product is so good that I have absolutely no issues with it and have ordered more for various other plastic repairs I need to do! Given how good it is, I think it's pretty good value, too.

Absolutely brilliant gear. Took a bit longer to set than advertised but once set it’s absolutely solid, used it to fix a handlebar switch that had come apart saved me buying another at a lot more money

Sets incredibly hard in about 15 minutes, allowing you to fill structural gaps and sand it down flush. I used it to fix a vacuum cleaner hose and worked brilliantly. Thought of many more uses for it so can't fault it.

Great product-

Great product I used this to stick my two plastic panels together on my car door mirror as it kept coming apart, it seems quite runny to start with and once set it's done a great job seems very strong too. Would recommend this product

Used this to attempt a repair on a cracked car boot trim plastic panel - with mixed results. The product description doesn't say it is only marginally compatible with polypropylene. Also, the stated cure time is way too short - it takes 48h+ at 20C to fully harden. The trim panel had a crack at the corner of an access hole for the rear lamp cluster about 4" long. I applied JB Weld to the interior of the trim panel where it's not visible, to fix both halves of the crack in place. 1st attempt: mixed using the supplied wooden spatula and the packaging "mixing tray". No prep on the plastic panel except for degreasing and cleaning. Gooped up the interior of the panel and worked the compound into the crack. Left to set overnight in a warm garage at 20-25c. Next morning, after 16 hours, the remainder in the mixing tray and on the panel was a slightly pliable tacky mass, like sun-baked chewing gum. Also, the bead that I had laid on the trim panel had started to come away from the plastic at the edges. 2nd attempt: scraped the half-hardened epoxy off with a razor blade and sanded the area with 120 grit sandpaper and degreased (again). Mixed another batch with a proper spatula and bowl, and gooped the crack again. Left in the sun, with plastic temperature approx 50-55°C for about 4 hours. Noticeably harder after this than the first time. Adhesion appears to be much better, and the edges still adhere to the plastic. Time will tell whether it holds up.

I used this glue as my splitter on my car was coming off and its been a couple of days and it looked like its holding very well. The instructions are very easy as simple and the drying times isn't too bad.

15 euros de contra Ren bolso aparte del producto

Nice and efficient, be careful when you use it, it gets hard very quickly

Es un gran producto, nunca había usado un pegamento epóxico, y para ser la primera vez ha resultado muy bien. Logré pegar una pieza rota de mi laptop. Esta pieza forma parte del soporte de la bisagra izquierda, al inicio creí que no soportaría el movimiento constante, pero seguí las recomendaciones y tips de otros usuarios, lijar un poco la superficie (utilicé un pedazo de lija fina pegada a un picadiente debido a que el espacio era bastante reducido), limpiar (usé un cotonete mojado con alcohol isopropilico), luego apliqué el pegamento y dejé secar por alrededor de unos 4-5 días sin aplicar movimientos y el resultado fue bastante satisfactorio, el pegamento seca en color negro un poco esmalte, pero en mi caso no se nota tanto porque el chasis de la laptop es negra. En fin, funciona muy bien y es muy resistente, lo recomiendo mucho, te va a funcionar si sigues las instrucciones.

Bought it to repair the windshield pillar on my car. After mixing the product it takes around 20 to 30 minutes to start becoming harder. After an hour it hardens and it has a little rubbery texture. I sanded it and painted it afterwards, great result and easy to use.

Works on my plastic real well