Arctic MX-6 (4 g) - Ultimate Performance Thermal Paste for CPU, Consoles, Graphics Cards, laptops, Very high Thermal Conductivity, Long Durability, Non-Conductive, Non-capacitive

I replaced my old pre-applied AIO thermal paste with Arctic MX-6, and the results are impressive. My setup is an Intel i5-13600K with a 220 mm AIO. Before repasting, the CPU would instantly spike to 100°C and thermal throttle during Cinebench.After cleaning and applying MX-6 (X-pattern), temperatures dropped significantly. Now the CPU runs at ~80–82°C under sustained Cinebench load, with no throttling. Idle temps are also noticeably better.MX-6 is a thick, non-runny paste, which makes application easy and prevents pump-out over time. It doesn’t look wet, but that’s normal — it spreads perfectly once the cooler is mounted.Overall, MX-6 delivers excellent thermal performance, long-term stability, and great value for money. Highly recommended for both air coolers and AIO liquid coolers, especially on modern Intel CPUs.Compared to the old paste, MX-6 reduced peak temperatures by 15–20°C, confirming much better heat transfer and contact.The 4g pack is more than sufficient. After applying once on my CPU, I still have enough thermal paste remaining for at least 2–3 future applications.

After using ARCTIC MX-4, I wasn’t impressed — my temperatures stayed high, around CPU 100 °C and GPU 87 °C under load (maybe a bad batch). I watched a lot of YouTube videos, and most say there isn’t usually a significant difference between thermal pastes, so I didn’t take any images for MX-4.But after switching to MX-6 (4 g), the difference was immediate and dramatic. My laptop now runs at around CPU 93 °C and GPU 73 °C under the same test conditions (photo posted).Even though I’m not sure about the exact viscosity difference, the MX-6 paste stuck much better to the CPU and GPU surfaces during application and removal. It feels thicker and more stable, with none of the squeeze-out problem I had with MX-4.For the small price difference of about ₹190 (during sale), MX-6 is absolutely worth it. It performs better and gives more consistent thermal contact. Highly recommended!I’ve also tested Thermal Grizzly Conductonaut (2 g) — the review for that is available on this page as well.

It is non conductive thermal paste,I have tested before applying.I have applied on my asus vivobook pro 15 m3500qc notebook but I don't any changes in thermals it is similar to stock one.

This temperature drop of 10-15 degrees is remarkable and instantaneous. The thickness is ideal for spreading and application, making it a reliable choice. I personally utilized it in my previous build last year, and its exceptional performance left a lasting impression. I have since reordered it for my new build due to its durability. Its outstanding performance, especially on full load of the latest top-tier AMD processor, makes it an excellent choice for gaming. I highly recommend purchasing this product.

Very good thermal paste it reduces my cpu and gpu temps significantly in my laptop it's is value for money for the performance it offers . It is very simple to use with a cap on top to protect from leaking . It can be used with every cpu cooler gpu chips . The thickness is nice . Its compatibility is with every cpu gpu chips

The compound is too thick and it does not stick to the cpu die making it frustrating to use. After getting it applied somehow, my temperature is too high to go past POST, needing another repaste. Very disappointed with this.

Genuine product. Easy to use. Very effective. My earlier local thermal paste was still overheating my laptop and making my fan move fast. This MX-6 almost immediately cooled the laptop and hardly any fan noise also coming now. Temp is also almost 15-20 degrees cooler.Just remember when removing old thermal paste clean with isopropyl alcohol and use a clean soft cloth to remove all residue.Apply a pea size amount of MX paste. Don't spread but put the heat sink / cooling coil carefully without pressing or pushing.Once you tighten the screws of the Heat sink the paste will spread automatically and evenly.Switch on thr laptop and let it warm up and the paste will spread properly.

This is the first time I bought thermal paste after doing a bit of research and it's pretty good for price as it has 4gm of thermal which is more then the competition I got it for 600 rupees which seems responsible I changed my laptop and laptop both cpu and gpu thermal paste and still 2gm of paste left.On pc the temps where hitting 80-90 centigrade and now the max temp is between 72-74 and on laptop the max temps while gaming was above 90 and now in 80s which is improvement.If you're doing for the first time look for guidance on YouTube as things can go wrong I pulled out the cpu with fan while removing it was stuck to the cooler Good luck

It works really well to keep temps low BUT it's chalky and dry as hell, no spatula in the world can spread this evenly. Arctic relies on the clamping pressure of your CPU cooler/AIO block to spread out the paste evenly, so if you're using this paste for something else or have an old laptop where CPU coolers won't exert as much clamping force this paste won't work. So be aware of your intended use case for this paste and proceed.

Initial Impressions:The Arctic MX-6 arrives in simple, no-frills packaging with a protective cap and an applicator included. The syringe design makes application straightforward, and the paste itself has a smooth consistency—thicker than some cheaper pastes but still easy to spread.Build Quality & Design:Arctic has a strong reputation for thermal compounds, and the MX-6 feels like a refinement of their earlier MX-4 and MX-5 formulas. The paste doesn’t separate or run, and it has a dense texture that stays where you put it. The syringe is sturdy and precise, allowing for controlled application without waste.Ease of Use & Performance:Application was simple—just a pea-sized dot on a CPU before installing the cooler. The paste spread evenly under pressure, with no air bubbles or excess mess. In testing, CPU temps dropped a few degrees compared to my older MX-4 paste, and load stability was excellent. The performance gain isn’t dramatic if you already use a high-quality thermal paste, but it’s noticeably better than stock compounds or budget pastes. Arctic claims long-term durability, which is consistent with their past products that often last 5+ years without drying out.Value & Comparisons:MX-6 is a little pricier than older versions, but the performance, stability, and ease of use justify the cost. It doesn’t have the highest thermal conductivity on the market compared to exotic liquid metal compounds, but it’s much safer (non-conductive, non-corrosive) and more user-friendly. For everyday builders and gamers, it strikes an excellent balance.Pros:• Smooth, easy-to-apply consistency• Non-conductive and non-corrosive• Noticeable improvement over stock/budget pastes• Long lifespan without drying out• Safer than liquid metal optionsCons:• Slightly more expensive than MX-4/MX-5• Gains are modest if upgrading from a good paste• Not as extreme as liquid metal compoundsVerdict:The Arctic MX-6 is a dependable, user-friendly thermal paste that offers a solid balance of cooling performance, safety, and longevity. It won’t replace liquid metal for extreme overclockers, but for most PC builders and gamers, it’s one of the best all-around options on the market today.

goed spul

Die ARCTIC MX-6 Wärmeleitpaste macht genau, was sie soll. Sie lässt sich mit der Spritze sauber dosieren und gut auftragen, die Konsistenz ist angenehm zu verarbeiten. Da die Paste nicht elektrisch leitfähig ist, kann man sie auch ohne großes Risiko verwenden. Die Temperaturen sind nach dem Auftragen im grünen Bereich, und alles läuft stabil. ARCTIC liefert hier bewährte Qualität zu einem fairen Preis – klare Empfehlung.

I put new paste in me and my wife's PC every 8-12 months(during deep cleaning). This paste seriously goes above and beyond. 100% helps to keep the temps down even under heavy loads. I have a Strix ROG 3080ti with an Intel Core i9 11900K and a Lian Li 360 Galahad. I play Apex with all high settings, temps hold around 63-65 no issue. I use the Pea sized dot method