1 Button & 3 Receiver

Very good, same battery's for 3 years

So easy to set up. Stuck it outside on front door and plugs in 3 sockets around the inside of the house. Took me all of 5 minutes! Good, loud bell.

I’ve given it 4 starts as finally it worked well and sounds great. HOWEVER, someone at the factory actually put the battery in the wrong way round. Almost sent it back until I noticed the battery problem!

Ding Dong!! Easy to pair with older Physen doorbells and ringers, in fact it was simple to do. Good quality, loud, easy to install and lots of ring tones to choose from. I’d recommend without any hesitation.

Actual requirement was for TWO bell pushes and three plug in units. After searching I could not find this combination. So with some reservation I ordered two sets of one bell push and three plug ins, hoping that they would pair. Goods were received next day (which was excellent) and the sets all paired together with no problem. The sets were very well priced and I would certainly recommend this seller both on service and price

Good product that was easy to set up and install. I probably should have got one with more receivers but 3 will have to do. Now I can hear when someone presses my doorbell no matter where I am in the house or garage.

Very happy with this doorbell. It is very well boxed which gives a positive impression and just works and is easy to set up. It is well priced compared and got five audio levels from silent to VERY LOUD. It has 3 sounders which works very well and is useful. We put one sounder unit on the ground floor, one on the first and one on 2nd which is perfect.Many of the 'sounds' are in fact tunes, classic and seasonal melodies, a selection of standard 'bing bong' sounds and a few unexpected ones too. The audio quality is very good. In short I am happy with my purchase.

The receivers pair with & respond correctly to my existing Physen bellpushes as well as the bellpush in this pack.The receivers sound off when any bellpush is pressed as do my existing Physen receivers now I've paired them all.I first bought Physen bellpushes & receivers in 2018 and they have been in use ever since without any problems whatsoever.My existing bellpush is on my [wooden] front door and is very well sheltered by the porchway.I'm soon having my door replaced with a uPVC one.- uPVC doors contain metal bars that give them their strength.- Those bars will hinder the bellpush's WiFi signals.I'll have to seek the builder's advice about a good location for the bellpush.If it will no longer be sheltered by the porch, I'll build some sort of housing over the top of it to prevent water incursion since I'm always skeptical of "waterproof" claims. Having said that, the new bellpush clearly has an improved seal around its edges so perhaps I won't need to add a housing.Despite the fifty something 'tunes' available I set mine to ding-dong, ding-dong. I think there are about half a dozen others that I might be happy with if I get fed up with ding-dong, ding-dong.One very good improvement in this product is that there are now forward & back tune selection buttons on the receivers.[My old Physen receivers only have a forward button so, if I click again after finding the tune that I probably want, I have to go all the way round the houses to get back to the desired tune.]I now have a receiver in every room.- All my receivers are set to maximum volume. The receivers do have lower volume levels [that I don't bother with].- If I am in a room when the Physen receiver goes off, it startles me even if I have the telly/music on loud.- If a Physen receiver goes off right outside the room & the door is closed, a loud telly/music can drown it out.The battery in the doorbell is type Energizer A23, Duracell MN21 [one comes with the pack so there's no need for a separate purchase yet].I have only had to replace the battery once since 2018.The receivers are mains-powered so they have no batteries.The review dated 17 July 2019 that says there is no battery in the bellpush must be referring to a different product.The error in the instructions:- In the diagram on page 7, the labels for the Up & Down buttons are accidentally reversed.- In para 7 on that page, the Reset procedure is initiated by long-press on the button next to the Volume botton [and not the one furthest away from it as the incorrect diagram labelling would have us believe].- I have tested the corrected Reset procedure on all three of these Physen receivers & on another I bought a few weeks ago.[Several old reviews make me think that people were unable to Reset their receivers in order to start again.]The problem for which I needed to Reset a receiver was that, after I had paired it with an additional doorbell, the receiver started sounding off randomly & of its own accord even when no doorbells were being pressed.Now that I have used the corrected Reset procedure, the problem has disappeared.I have re-paired the problem receiver with every doorbell & it once again works correctly, it only sounds off when a doorbell is pressed.

Bonjour,Les recepteurs ont des bornes Anglaises/Américaines et non adaptables sur prisr en France !Pouvez-vous m'envoyer les bonnes svp