AKNES GuliKit TMR Electromagnetic Joysticks Replacement for DualSense PS5 / PS5 Edge Controller, Thumbstick Grips for PlayStation 5 Controller, Thumbstick Caps Included

These TMR sticks feel very nice once installed, and seem to perform flawlessly, at least so far. Stick tension and press-to-click are essentially indistinguishable from the stock ALPS units. No more drift! Don't take the warnings about install difficulty lightly, removing the original stick units is very difficult and if you don't know what you are doing it's quite easy to irreprably damage your controller's main board. The lead-free solder Sony uses in the Dualsense has a relatively high melting temperature, and coupled with the large metal area of the stick cage desoldering is a @#&$. A hot air rework station may make it easier, as you can heat a larger area... I was able to do it with a decent Hakko-style iron, but this is really NOT a job for novice solderers. If you've never soldered before, or don't have much experience, prepare to be very frustrated. Don't say you weren't warned!

These worked fine. Installation was easy. A lot of people recommend having soldering experience. The soldering isn’t the problem. I recommend having DE-soldering experience. That’s definitely the hard part. Especially with components that have multiple pins and even worse, multiple pins on different sides of the component like these joysticks do. Compounded by double layer PCB’s because you have to remove the solder from the joint AND all the way through the hole to release the pin from the board. So how do you do that or how do you heat the solder on 8-10 pins at the same time to remove the component? That’s the challenge. I can tell you how I did it, but I don’t recommend it because it’s risky and you can very easily damage the PCB beyond repair. I think I saw some tools that allow you to heat all of the pins at once. That would make this a simple job if you can find and afford one of those and I’d consider looking into it if I have to do this again. Otherwise you can risk it and do what I did which was to cut the pins between the component and the PCB with a dremel. That way you can desolder and remove one pin at a time. But one slip and touch the board with the Dremel blade and you can, and probably will ruin the PCB. I’m not sure if you can buy a replacement PCB but swapping that would really suck and at that point I think it would be better to scrap the repair and just buy a new controller.

A MUST FOR GAMERS! If you ever get tired of STICK DRIFT or just the sloppiness of your toggles and want not only a durable upgrade but a technological one as well then this is your one stop! TMR toggles are accurate no drift and recalibration is available to tune them!! Grip is amazing and fits like a glove! YOU DO NEED TO DESOLDER AND SOLDER! but a heat gun on low does the job for the inexperienced. Strong build but be wary of northern most button its brackets are a bit brittle before installation. Quality is off the hook with none of that cheap controller feel BEATS OEM BY GALAXIES!

Fixed my ps5 controller.

One stick defective out of the box

The best ever if you want a good change and quality in your controller buy it

I bought a 2-pc set of these to install in a PS5 joystick that developed the dreaded "drift" problem. This also meant I spent time learning a new skill, soldering, so that I could do the work of swapping out the old bad joysticks with these new ones. A few weeks of practice on several beginner level soldering kits, along with one painful lesson on just how hot 400 deg Celsius (about 750 deg Fahrenheit) is when you clumsily graze your finger with the soldering iron, and I went to work on my PS5 controller. For me, and I think just about everybody else that I saw on YouTube, the hardest part was (1) getting the PS5 shell open, (2) de-soldering the old joysticks (I only had manual solder pump and wicking wire) to be able to remove them, and (3) being careful not to melt any adjacent cable connecters with the soldering iron because it can get a little tight to maneuver in there. But after managing all of that, soldering in these Gulikit joysticks, getting the controller back together, and using online tool to calibrate them I was all done. With my inexperience it took about 4 total hours, with the de-soldering step really taking up about half that. I've used the controller for about a month now and it's been great. The joysticks move very smoothly and I am able to move my character with really good precision. The only thing I noticed is that they don't have the same resistance as the original joysticks. What I mean is with the original joystick (made by Alps) when you start to move it, in that first 1/4" distance you can feel a little more resistance that then fades away as to continue to move the joystick farther out to the edge...hopefully I'm getting that across well enough to understand. With these Gulikit joysticks that little resistance is not there...but that's not really a knock against them, just an observation. The only knock against these, and the reason for the 4-star rating instead of 5-star, are the included thumb sticks and rubber joystick caps. In my opinion, the thumb sticks don't have as good a grippy texture as the original thumb sticks, but the included rubber joystick caps are definitely more grippy, but I just don't quite care for the star pattern design on them. But I play with them anyway and they are great...just not great to look at in my opinion. Maybe in the future they could offer some color and pattern options for the rubber caps??? An option for you if you feel the same is to simply not install the included thumb sticks, and instead just reinstall the original thumb sticks on top of the Gulikit joysticks. Now, whether these will stay calibrated and never fail or develop "drift" in the future remains to be seen. They use magnets so technically speaking they never should but only time will tell.

Ich bin froh, dass ich mich dafür entschieden habe! Die Sticks hat mit ein Kollege empfohlen und ich hab sie nach dem Einbau einem Anderen Kollege empfohlen. Ist es aussagekräftig? :-) Da wir alle Elektroniker sind war das kein Problem die Sticks auszutauschen. Funktionieren einwandfrei, nur etwas zu empfindlich. Bei BF6 zum Beispiel habe ich die Deadzone etwas vergrößern müssen und zocke damit schon seit Monaten ohne diesen Standart-Drift, was bei PS5-Kontrollen zumindest bei mir in beiden der Fall war. Klare Empfehlung!

Ze doen wat ze moeten doen. Het kalibreren was ook totaal niet moeilijk. Zeer blij met dit product!

Nice and good 👍👌

Los he instalado en un DualSense de 1ª generacióm y después de calibrarlos, funcionan perfecto. Són muy precisos, suaves y tienen una circularidad impresionante (lo puedes comprobar en la foto). Són muchísimo mejores que los originales. Pero se tienen que calibrar, eso sí; pero es muy fácil si sigues las instrucciones. Lo único es que cuesta un poco dessoldar los originales y si no tienes las herramientas adecuadas (hierro de soldar, bomba de solda, etc.), o bien las compras y te van a servir en el futuro para hacer este tipo de reparaciones, o los llevas a una tienda de reparaciones electronicas y te los instalan. Pero eso no tiene nada que ver con la calidad de estos modulos, que són muy buenos.

Works great. A bit expensive but still better than buying a new controller. The movement is smoother with this. Takes time to adjust to the joystick movement with such low resistance. Don't forget to calibrate it with the online website