Ringke Dual Easy Film [4-Layer Protection] Compatible with OnePlus 13 Screen Protector, Self Healing Repair Coating Full Coverage Screen Protector - 2 Pack

Hard to install. Bottom half of screen came off on step 1 and made it pretty hard to install correctly.

If you're having issues with the install of this protector, have patience and watch the install video of the protector on the product page. After viewing that video and following along, the installation of this screen protector was smooth and I had minimal air bubbles that dissipated within 24 hours of installation. As a side note, if you're coming from the stock screen protection film, make sure that you remove that film and then immediately place the new protector down on the phone to help minimize any kind of dust contamination. I would suggest also to place the screen protector guide into the usb c port prior to removing the stock film. This protector also has a built in kind of dust remover with the first section of the process. Just remember patience is key with this type of plastic protector.

I bought these long ago and they sat unused as I left the factory screen protector on for almost a year. This is my first screen protector that came with an alignment jig. I'm used to carefully aligning an adhesive sheet, then dropping it onto the screen hoping to getting it right. I read the directions and thought I understood the process, but was disappointed. I thought they sent me the folding phone variant because of a horizontal line in the middle, but proceeded to do the install anyway as I had just removed the factory cover and wanted something on the phone until I could order something else. I had huge bubbles and mysteriously had dust trapped where there was none when I started. I reread the directions and realized there was another step I was missing. Watched the online installation video and it all became very clear. 30 seconds later and the screen protector was installed and almost perfect. I'm going to deduct one star for the packaging instructions being unclear and one bubble after the initial install. I'm hoping it goes away in time as the instructions promise. It is located under the #4 tab so I couldn't see it while smoothing the rest of the protector. The screen is crystal clear. Scrolling feels smooth and slippery. Fingerprint reader works as usual. I don't use the selfie camera often, but having the protector over the camera doesn't appear to affect the photo quality. The small cut out in the factory protector was a spot for dust to collect so I appreciate this detail. So overall a really good screen protector that suffers from poor instructions.

You need to be careful installing these types of screen protectors as the film is not solid and will warp easily. First install I had multiple bubbles close to the edges. Was able to scrub a few out, but ended up cutting a hole in the protector. Second install was much smoother. Still not a big fan of the noticeable line left across the screen. My advice while following the instructions, when installing each halve, apply pressure short of the halve while attempting to remove the second and third tabs. Then apply a good amount of pressure when sliding the tabs out with the squeegee. If you have a curved screen, after removing all 4 tabs, go back through with the squeegee and with outward strokes push down the edges so the film applies to the curve. I always thought a second protector was supplied in case the first broke, but this one I'm convinced the first one is provided as a test install.

Terrible. First, they shipped it in the original packaging and put the shipping label over the instructions. *Eye roll* When I finally got to the instructions I followed step 1 and removed tab 1 and half the blue protective layer came off. Instant dirt on the film and no way to put it back together to even attempt install. Second film got all the way on but then there was a tiny piece of film attached to the outside of the installation layers that prevented me from removing the bubbles underneath of it. Attempted to work them out but they wouldn't budge. Of course, they were over the front facing camera so I couldn't leave it on. 2 for 2 down the drain. Don't waste your money. Honestly, they are made of what feels like 4mm plastic film. Don't know how that would protect the phone if something hit the screen but I couldn't use it long enough to find out.

Best and easiest protector I have used. Only needed one and was on my OnePlus 13 phone in 2 mins. Used this brand for my OnePlus 12 as well. If you have bubbles they will be gone next day and it does heal on its own. Very good product.

First and foremost, my fingerprint reader is still completely 100% functional after installing this screen protector. It feels nice but I can see how it would wear out much much faster than a glass screen protector. Now, this is my first Ringke screen protector, so, even though I read the instructions several times, watching a video is night and day vs trying to read the rediculously tiny print on the back of the box. Once I watched that, it was a pretty straight forward install. Note here: while your box may contain TWO protectors, they have only included ONE wet wipe for cleaning. If you hesitate or take pause when sliding the squeegee tool , you'll have a line in the film. So one fluid sweep up and off the top, and one fluid sweep down and off the bottom should keep things looking clean. The sticker tab for 4 ( the final peel) gets in the way of sliding the squeegee tool when installing the top half of the protector. I'm not sure what the workaround would be for that. All said and done, I think the protector is satisfactory. If anything changes as I use it, I'll make note of it and edit the review.

Wish I read the comments before buying awful instructions and terrible way to apply it. Both came off the jig too easily as I was taking off a layer and went crooked and trying to eyeball it to get it straight just added more bubbles that could not be taken out by the squeegee no matter what I tried. Awful

Terrible product which is overpriced and overrated. I ve been using ringke case for my oneplus 13 for more than 8 months and it is perfect in every sense, the trust was extremely broken when I received the dual easy film for my oneplus 13, it is not an easy task for applying but also leaves a line across the screen even I was fully aware of the product application and take well care during the process, still it leaves a line across the screen which is annoying, the suprising part is the product is highly overpriced for such kind of cheap product.

I am very disappointed with this product. You get 2 in the pack and I have used both of them. Both of them have a line in the middle where the 2 pieces of the protective cover meet. Although the description mentions those the line does not go as it says it does. Also the application of the protective cover is so difficult it is almost impossible to not get bubbles. While the second application was much better than the first attempt due to understanding what the process was I sill have 6 bubbles which I cannot get rid of. This is going to need to be replaced. My advice is to buy a different protective cover as the application for this one is too difficult for it to not look like a mess after.

I got the 2 protection films, and both were disappointing. After applying the first film, I noticed right away that the edges and corners just wouldn’t stick properly. I thought maybe it was a defective piece, so I tried the second one but same issue again. No matter how carefully I applied it, bubbles kept forming around the corners, and they wouldn’t go away. It just doesn’t adhere well at the edges at all. For something that claims to be easy install, this was frustrating and a waste of time. Definitely feels like low-quality material.

Oneplus 13ですが、マイクロクアッドカーブディスプレイを採用しており、 四辺全てがR面となっております。 非表示部がカーブしてるだけなら良いですが、Oneplus13は表示部からカーブしています。 エッジディスプレイよりかは緩やかではありますが、 表示面の四辺が全て緩やかなカーブとなっている為、 必然的に保護フィルムの選択肢が狭まります。 硬化フィルム系は全面保護するものは無く、ガラス系もエッジ部は接着剤が無い、等。 こちらの商品はEPU素材なので完璧に全面保護してくれます。 ですが、やはりガラス系と比べたらスクラッチ耐性は弱いので、 定期的な張替えが必要になるかと思います。 曲面ディスプレイの保護フィルム選びは中々難しいです。

There were two in the set. I used both, but it was a waste. Please don't buy.