UTP-X Ultra Thermal Putty,Cooling Pad for GPU VGA IC Processor,100g

This stuff is AMAZING. Absolutely amazing. I cannot recommend it enough. I'd been struggling with thermal modding my Powercolor 9070XT Red Devil for a few weeks now. They must use some weird proprietary sizing for the VRAM thermal pads, as 1.0mm was too big and prevented core contact, but 0.5mm was too small and led to warmer VRAM temperatures than I'd like. So I relented and bought this stuff after hearing great reviews, and it was entirely worth it. Being putty, I didn't have to worry about sizing at all. It squished down perfectly and now I have probably have the coolest VRAM on any air-cooled 9070XT. I added 5mm pads to the backplate behind the VRAM in addition to this putty, and now my temps don't even see 70C at 4k ultra in any game. It's magnificent. It was super easy to apply as well. You just scoop it up and push it down on the VRAM chips, then the cooler mounting does the rest. I truly didn't think I could get the chips this cool without water cooling. Overall 10/10. I'm running a +400MHz overclock on my VRAM and it doesn't even care. My GPU is quiet, cold, and calculated. I'm never using thermal pads on my VRAM again. This stuff is a cheat code.

Really nice and cool thermal putty, I applied it to my SSD NVMe on my laptop, very easy to apply.

So i had an issue. I have a VERY obscure graphics card that seemingly nobody else on earth owns (HP Omen 3070ti) that had horrible thermal issues. It also had incredibly weak mounting pressure so not only could i not find proper pad thickness info anywhere online but the mounting pressure was so weak trying to find the exact combination of soft and hard and thickness of pads was impossible, if i was even the tiniest bit off i'd get uneven die contact and hotspot issues so i gave up on pads and decided to try putty. If you have a worst case scenario like me where mounting pressure is THIS bad putty is the way to go. Mine was SO bad even the squishyness of the putty could prevent proper die contact but putty is so easy to work with all i had to do was keep cutting a bit off and remolding it till i got good contact with virtually zero resistance. Combined with PTM7950 the results speak for itself. My card went from 85c core temp with 105c hotspot under load with 100% fans to 65c core temp with 73c hotspot under load with fans going about 35%. Most of that is the PTM but i NEVER and i mean NEVER could have gotten proper gpu die contact with pads. I tried for 3 days and it just didn't work. With a card that's not total garbage like mine you can just put putty down, squish it down and repaste and forget it. No measuring of pads, no cutting, no nonsense and it works so good. Amazing product and so easy to work with. I'm NEVER buying thermal pads again.

En cuanto a rendimiento térmico es excelente, no hay quejas , las memorias se mantienen en rangos óptimos por debajo del promedio de calor que determina el fabricante de la gráfica, no se puede estimar los grados a lo que va a trabajar porque cada gráfica es diferente y la ubicacion, humedad y calor geográfico son determinantes, hay que tener claro que tanto aplicar está masilla como una lámina de PTM en el silicio va a aumentar la eficacia de traspaso de calor hacia el disipador comparándolo con pasta térmica y pads, pero aún así la disminución va a tener el tope que tenga la temperatura de aire que introduzcan los ventiladores al case y que tan efectivo trabajen esos ventiladores sacando el aire del case, un efecto que se va a sentir es que fuera del case mas bien se siente mas caliente el aire y esto se debe a que la eficiencia de traslado de calor de esta masilla y del PTM son mucho mejores, por lo tanto las temperaturas que puedan mostrar programas de lectura de sensores van a ser menores pero la sensacion de calor en el escritorio va a aumentar como mencioné antes asi que se ocupa de ayuda extra como mas ventilación natural, ventiladores o aires acondicionados para el comfort del usuario, porque internamente el hardware si va a funcionar mucho mejor. En cuanto a la aplicación es un poco más complicado de aplicar que el upsiren rosado, pero es básicamente hacer bolitas de unos 4mm, apretarlas "MUY" poco solamente para ayudar a que se mantengan en las memorias de la GPU y luego asegurarse que antes de poner el disipador contra la placa que tengan la "montañita" de producto mayor al espacio que queda entre memoria y disipador, y luego por nada del mundo hay que hacer presión luego de poner el disipador, con la propia tensión que generan los tornillos es suficiente para que la masilla se baje y haga buen contacto y solamente es necesario aplicar un poco de presión en caso de que la placa de la GPU se vea un poco doblada.

Used this to revamp a 3080 FTW3 12GB. The card is known to have slightly off pad sizes. I wouldn't consider any putty "easy" to apply but it eliminates fuss over pad sizes and tension when applied correctly. While time consuming, it's a great one stop pick. If you intend to use this on your VRAM like I did you might need more than 20g. I used about 35g. The card never had serious cooling issues but this brought the hotspot down 4c from 80c, more notably MOSFETs/VRAM/Power never break 65c, all thanks to improved thermal transfer. I should mention this is all on air in a sub tropic area. Very much worth it if you're willing and careful.

This is extremely dry and stiff. I found it difficult to apply using the spatula, so I ended up using my hands. Be careful not to use too much, since it doesn't really squeeze out like paste and some other thermal putty. Seems to work fine though.

I got tired of getting worried about buying the right size thickness of replacement pads after buying two XFX RX 7900XTX Merc310 video cards I wanted to repaste with MX-6 on the GPU die. I never trust OEMs on using premium thermal paste or pads, and I was right. One card had too little paste, the other bubble areas from pump out. Forget using the spatula for anything other than just grabbing a bit of this stuff out of the bottle, go for full coverage rubber, nylon, whatever gloves. I learned it's best to start the flattening process yourself with a single finger. Use the spatula to cut off excess, but be ready for this stuff to come apart and get stuck to your gloves when you least expect it. Cleaning the surfaces with 91% or above isopropyl alcohol helped it to stick especially on the VRAM. **One major note. Expect to use 1 full bottle of the larger size of this stuff per graphics card (GPU). Each VRAM row in my card was 8GB, so 3 full rows of VRAM for the 24GB. Add in the capacitors, ICs, other originally covered with pads and I can guarantee you it's best to have a full large bottle versus 1 small bottle per card!!** it was worth it though. The VRAM temps alone from this stuff dropped about 8C without load and almost 10C under load. Was it perfect application..probably not but who cares.

For what it's worth, ADHD hobbyist review and comments. Summary at end, here's TLDR: Seems to be intended for highly mobile and vibration prone applications for it's resistance to applied forces and dense consistency. If vertically mounting or securing to a vehicle based use, this may be a good option. Be sure of your intended use case! UX Pro Ultra is a fairly stiff product and may cause unexpected inconsistency in thermal performance where mounting forces are carefully balanced. It can be squished to perfect gap thickness, but could interfere with critical tolerance components if pre-prep isn't thorough. Hopefully not a knockoff clone, but seems to work well. Medium grey colored and a but crumbly when moved, has a notably dry consistency, and is difficult to work with. More of a "spreadable thermal pad" compared to some salvaged contaminated K5 pro "liquid thermal pad". Upsiren UX Pro Ultra has a strong tendancy to stick to itself and any surface it has been worked on or rubbed into, so after cleaning the surface for application it's recommended to take a small amount and work it into the contact area until residue can be seen left behind. Absolutely wear gloves if there's chance of touching the UX Pro, and clean or change frequently as well as the provided spatula to avoid sticking large amounts for ease of application. If possible, something like a clipped dental irrigator for precise application is recommended. Overall, only a marginal improvement over K5 Pro for thermal efficiency. I would recommend reserving for use cases where strong mounting force is possible as UX Pro Ultra will peal away from applied surfaces fairly easily due to it's preference to adhear to itself. Performance margin is negligible unless heat dissipation is truly critical, especially when direct contact or use of precise shims are possible. Major difference in difficulty of use, but notably UX Pro Ultra will be much easier to clean and salvage due to it's tendency to stick to itself compared to K5 Pro that is much more paste like and sticky. If concerned with K5 Pro possibly running out from place, I would note that I have K5 in use long term in vertically mounted gpu as well as gaming laptop for travel that is normally stored vertical not flat. In 3 regular maintenance/cleaning checks at 8month intervals I have noticed no runout of K5 Pro at all. UX Pro Ultra may be best for non-critical high heat components, or otherwise extremely mobile and vibration prone applications.

Highly effective. But a pain to shape and apply. If you have used putty before this is a great product if not be ready to spend lots of time to do all the vrms and components. Stick to thermal pads if you dont have the paitience but if you need actual performance go for it. Highly satisfied.

La use para mí tarjeta gráfica y va muy bien mantiene las temperaturas correcto entre 70 y 78°c a máxima capacidad, es de fácil manejo y la cantidad correcta para una tarjeta gráfica grande

Works as intended on my ROG G15 laptop! Nothing much to say because I can't really track the temps of VRAMS and such, but my laptop is not thermal throttling, at least, right?

The items ordered are very small as per the chart, wrongly guided and even after talking to their advisor they are not changing which is very wrong and there is also an option to replace it