2 Pack Upgrade to 3600mAh 9000 Replacement for makita 9.6v Battery Compatible with makita 9.6V Battery Ni-Mh Compatible with 9000 9033 193890-9 192696-2 632007-4 6096D 6093D DA391D 6095D 5090D (9000)

I ordered these for my dad and he is very pleased with them. They hold a good charge and they are well worth the price.

Work as well as original. Returning because it's a duplicate order.

I CHECKED EVERYTHING TWICE AND ALL WAS IN ORDER. CORRECT REPLACEMENT BATTERY. THEY CHARGED FULLY WITHOUT ANY ISSUES. HOWEVER WHEN INSTALLED IN THE DRILL NOTHING ENGAGED THE DRILL TO WORK. I CHECKED THE DRILL BY INSTALLING AN EXTRA BATTERY THAT I HAD AND THE DRILL WORKED PERFECTLY. FOR YOUR INFORMATION THE ONLY ISSUE THAT I COULD IMAGINE WAS THAT FOR SOME REASON THE CONTACTS WERE NOT MAKING CONTACT WITH THE DRILL CONTACTS ONCE THE BATTERIES WERE INSTALLED. ONCE AGAIN I DON'T THINK THE BATTERIES WERE DEFECTIVE. THEY MERELY DIDN'T WORK WHEN INSTALLED IN MY MAKITA DRILL. IF YOU CAN FIGURE OUT WHAT WAS WRONG I WOULD CERTAINLY ORDER THE PAIR IN AGAIN. CORDIALLY, RICHARD ADDITIONAL COMMENT: THE PROBLEM I DISCOVERED IS WHEN THE BATTERY IS FULLY PLACED IN THE DRILL THE CONTACTS DO NOT ENGAGE. IF ONE PULLS THE BATTERY BACK OUT 1/16 OR 1/32 OF A INCH THE BATTERY ENGAGES. HOWEVER YOU CAN'T CLOSE THE CLIP AT THE BOTTOM OF THE HANDLE. I AM GOING TO KEEP THE BATTERIES AND I BELIEVE IF I JUST DON'T CLOSE THE BATTERY CLIP AT THE BOTTOM OF THE HANDLE THE BATTERY WILL STAY IN THE DRILL. IF NOT THEN A SMALL PIECE OF TAPE ACROSS THE BOTTOM SHOULD KEEP IT IN AND NOT GET IN THE WAY OF THE OPERATION OF THE DRILL. IF YOU EVER DO CORRECT THE PROBLEM I WOULD LIKE TO GET THE RIGHT BATTERIES TO USE. AS MENTIONED BEFORE YOUR BATTERIES SEEM TO BE WELL MADE AND YOUR DELIVERY AND PACKING WAS BEYOND CRITICISM. ONCE AGAIN, CORDIALLY, RICHARD

Good value

Work great. Longer run time them OEM.

Purchased a two pack of these batteries for my Makita drill. When they arrived, you could tell the quality was less than expected. However, both were fully charged, and they worked fine. Once the first battery ran down, I attempted to recharge. The battery fit into the charger fine, but it would not charge. I used the second battery, and it worked fine until it needed to be recharged, and I had the same result, battery would not charge. I went back to my old Makita battery, and it charged fine, however it is at its end of life and does not hold the charge very long. Learned my lesson again about buying Amazon products. Quality has significantly declined over the years.

We think of cordless tools as ubiquitous but they weren't always. The idea that a battery-powered tool could drill steel was ludicrous, the stuff of "Mission: Impossible". Then Skil released their 12v "Top Gun" cordless drill and it was amazing, could do things you wouldn't believe possible. The only competition was Makita, a strictly commercial duty line of tools. I found the 9.6 drill at a yard sale with 1 or 2 batteries, case and charger. It wasn't as good as the Skil but...I quickly added the right-angle drill, the 3.5" trim saw, and the mini-"sawzall" reciprocating saw that goes places the sawzalls don't. But rechargeable batteries were a problem and I mostly abandoned the tools over the last 20-30 years. Now, with these new batteries, they are back!!!

I have an ancient Makita variable speed drill I paid for in precious body parts back in the early 1990's that I wanted to get back into service lo these many decades later. The batteries I had for them wouldn't charge with my charger at all (well, they ARE 30+ years old!) so new Ni-Mh were in order. But I was concerned about whether new batteries would be charged by my ancient charger. The batteries got VERY hot while charging, but didn't smoke, melt or burst into flames, and I recall the original batteries often got very warm, too. I got one charged up, and popped it into the drill. Well, popped may be a bit of a stretch. It slid in and got kind of stuck. It's not a perfect fit, with it being VERY hard to pull back out (I used channel locks to get it out afterward). But the drill performed flawlessly after that, so overall, the operations were a success, and I have a very high quality, rugged portable drill for the cost of new batteries for it. In my 4 star rating I didn't ding the batteries for being hot while charging. That does happen with Ni-Mh batteries. But I did take a star off for the poor fit. The old batteries slid in and out without any problems and APPEAR to be the same size and shape. These will require some judicious sanding to get them to slide in and out without hand tools being needed to extract them. That's not a hard thing to do, so I only took of the one star. For a (relatively) cheap fix for my "I don't have a working portable drill" issue, these batteries did the job.

Excellent product. Would not hesitate to purchase from them again. Purchased batteries from different company and two out of two batteries would not recharge.

Exelente

Tengo un par de herramientas Makita que utilizan este modelo de batería. MIs baterías originales eran de Nikel-Cadmio y estas son De Hidruro de Metal, lo que les da mayor capacidad y la carga no genera efecto memoria en la batería. El precio es bastante razonable comparado con el precio de las originales. Muy recomendables!

Perceuse sans fils, difficile à charge, bonne charge une fois charge

Batteries work fine. Make sure you use a Ni-Mh charger for these. If you use the Makita Ni-Cad charger that came with the tool these are intended for, they will overheat and be damaged. Amazon has one for 19.95 if you look carefully and batteries stay cool during charging. You can easily search online why you need the correct charger.