Addressable RGB PC LED Strip, 13.78 x 0.39 x 0.12 inches Clear Silicone Covering, for 5V 3-pin argb Header or AG-DRGB16 SignalRGB Controller(Not Included), Built-in Magnets, Easy to Install

Excuse my dirty glass, ran out of microfibres 😭 10/10 I am not a huge PC nerd by any means but this was very simple, quick, and easy to install. SUPER bright, lots of modes, its comparable 100% to the expensive lights you get in $4000 Pcs. My fiance has a $6000 PC with all the lights you can possible have and this set is very much equal to that quality! Plug and play!

Just wanted minimal accent lighting when I have the room lights off. This did the trick and the magnets grip very well but also easy to re-position.

Package arrived on Wednesday with everything listed. One strip did not work. I contacted customer service and they responded within a few hours. The following Friday (two days later) I received not a single replacement strip but a complete package. That’s great customer service! On to the product- installation is self explanatory knowing that you must install this to an addressable rgb 3-pin 5v header. Magnets are sufficient at securing the strip to a single straight run but trying to turn corners it may struggle, that’s when the adhesive helps out and holds the 90-degree turns tight. When connecting the strips in series or daisy chain, the light timings on each strip does not sync perfectly. There is a slight delay in the latter strip, maybe 1-2 second delay. In order for the timings to sync in both strips, you need them to run in parallel or use a splitter. The package does not come with a splitter, it comes with and extension. I used one of the included extra cables to make a homemade splitter and connect the led strips like that. Now both led strips sync up perfectly. Overall, I’m happy with the project and very satisfied with the customer service. The lights look great in my NZXT H1 case.

easy installation with good color accuracy and adhesive magnet quality. looks nice and isn't too sharp on the eyes. Length for me was perfect for installing on the top and sides of my pc but it has one caveat in the length department. For whatever reason, the motherboard 3 pin cable was installed onto the extension cable meaning if you use something like a fan hub that sits in the back panel / bottom of your pc area you will have to plan accordingly, if you plug it into your motherboard only though, you'll be just fine. solid quality on the magnets and lights no complaints but the end that isn't plugged into an extension does stick up so tape it down if you'd like.

works as described,bright ,flexible and well worth the $

This is a good discrete kit for adding addressable LEDs. The magnets make it easy to mock up and ultimately install the strips using the self adhesive. Be aware, for a Cooler Master RGB/Fan Hub the connector on the provided aRGB interface cable was a little too wide to fit into the hole in the Hub case. This would probably not have been a problem for my motherboard directly and it was easily remedied by trimming away some of the rubber on both sides of the cable's connector using a hobby knife. For those not wanting to modify the provided cable you may want to consider using a stock Cooler Master cable and moving pins between or splicing into the "three" pin locking connector used on the strips. It looks to be of the standard RGB LED, again "three" pin. I docked one star in my review on easy of install due to this, but otherwise I am very happy with the provided parts. They are bright enough for projected light to be seen behind a smoked acrylic cover of a Cooler Master case. I have them tucked under the upper and lower lip of the case. So far the are still in place and the adhesive appeared to grab well during install. For install and size comparison, in a CM TUF Q300L the LEDs reach the entire length of the upper and lower lengths of the case. The provided interface cable and extension worked to get the strips installed and wires routed out of sight. They are working with ASUS Aura on a CM RGB/FAN Hub perfectly.

I just wanted some lighting inside my chassis - didn't necessarily want or need flashy patterns or rainbow effects (although this has that too). I found it convenient to be able to just power this by SATA and use a remote control to change the color, as oppose to using the rgb header on my mobo. I usually just alternate between static colors to maintain a sleek/clean feel. For the value this as exactly what I needed. The strips are about the size of a typical side to a case and the magnetic adhesion actually works quite well and there's no slippage. Easy to install and works as intended, though some of the rubber was dried out, the strip cracked but that didn't impact the actual light strip, so a little tape fixed that right up. No malfunctioning LEDs or anything - worked great for my DYI build - good value for what I wanted out of it. I prefer the convenience of just using the remote control. My only criticism is that some of the colored buttons on the remote display inconsistent colors. For example I couldn't get purple from the purple button - it simply shines blue. But otherwise everything works fine.

There are a lot of LED strips for sale in a range of options at a variety of price points. This one fit my needs and was a reasonable price. I am really impressed with it thus far. The final test will be how long it lasts, but my initial impression is very favorable. I have the strips on the left and right sides of the case. They were easy to install, and the magnets hold the strips in place really well. I love that I don't have to use adhesive and attach them permanently. The cables that come with the kit are more than long enough to get the strips where I want them, and this is a full size case that will accommodate an eATX board. I feel the brightness level is perfect. Not too dim, but not so bright that they light up the room or anything. At this point, I have no complaints about this kit. If I have issues with it later, I will reach out to the manufacturer, and then update this review.

eccellente

One of the best items i buy it online and very Easy to fix 🙂👍🏼

ممتاااز

Je pense qu'il s'agit de "Aigoo", connue il y a quelques années pour des ventilateurs d’entrée de gamme à la qualité très discutable, car le logo, la police d'écriture est quasiment le même. Je ne vais pas tourner autour du pot : techniquement, ces bandes LED ne méritent pas 1 étoile. Elles sont suffisamment longues, aimantées (donc pas besoin d’adhésif), et je les ai même appréciées pendant quelques mois. Mais il y a plusieurs points importants à savoir avant d’acheter. 1. La poussière devient ultra visible Même avec un Corsair 5000D Airflow, pourtant bien filtré, la poussière reste visible. Les LED étant proches de la vitre latérale, elles mettent en évidence la moindre particule. Résultat : à moins de dépoussiérer son PC presque tout les jours (ce que personne ne fait), l’effet devient vite inesthétique. 2. Rendu des couleurs décevant Oui, on peut faire quelques dégradés. Mais le rendu n’a rien de “premium” ou de professionnel, même en blanc. Ça donne davantage une impression de configuration kikoo-RGB plutôt que quelque chose de sobre et maîtrisé. Pour quelqu’un qui recherche une esthétique minimaliste et propre, ce n’est clairement pas adapté, même avec un orange tamisé/blanc neutre, ça ne va pas. 3. Coil whine selon la luminosité Selon l’intensité choisie (trop forte ou parfois même trop faible), les bandes LED émettent un coil whine audible. Dans un boîtier posé juste à côté du bureau, ça s’entend. Et pourtant, le 5000D est relativement bien isolé. J’imagine difficilement le résultat dans un boîtier plus ouvert. Cela limite fortement les réglages utilisables sans nuisance sonore. Conclusion: Au final, cela reste une bande LED assez basique. L’aimantation est un vrai point positif, c’est d’ailleurs pour ça que je les avais choisies mais le rendu fait cheap, les couleurs manquent de profondeur, la diffusion est peu flatteuse et le coil whine est rédhibitoire. Ajoutez à cela l’obligation d’utiliser des logiciels comme SignalRGB ou OpenRGB qui tournent en tâche de fond en permanence… D’ailleurs, au moment où j’écris cet avis, SignalRGB rencontre un bug majeur : la dernière version génère des pop-ups d’erreur en boucle donc obligé de désinstaller pour utiliser son PC. Impossible de rester sur une ancienne version, car elle se met à jour automatiquement. Problème confirmé par plusieurs utilisateurs sur Reddit. Honnêtement, avec le recul, mieux vaut rester sobre : un écran Q-Code affichant la température CPU sur la carte mère suffit largement. Le RGB devient vite plus contraignant qu’esthétique, je voulais retenter le RGB, je voie que j'ai plus l'âge. Je ne recommande pas.

Not to bright, good magnets and integrate well, could be a bit cheaper but a nice buy.