RGBZONE 4Pcs ES08MA II 12g Mini Metal Gear Analog Servo Shockproof Stable Machine Compatible for RC Model

I have used these is some rc builds and regardless of vehicle type they are strong and reliable. I have installed these in a monster truck, shortcut car, a boat and one on a airplane and have had no troubles so far.

Excelente producto

Is good servos

clip the corners. fits fine. is lke 50 times stronger than the stock, its not even close. if you are mounting shocks on the frame it has plenty of space. if you are using the stock mount locations you might have to fiddle with the wire to get it right where you want it so it doesnt bind up your suspension.

I bought this to replace 2 servos that were jittering which I had unsucessfully tried to fix (ferrit core, reroute wire, etc). easy to replace and no jitters. I needed to reverse one of the servos and it was a breeze (reverse the 2 motor wires and reverse the 2 OUTSIDE wires going to the pot)

Received these yesterday to upgrade my scx24 c10 steering .. I 3D printed a new mount to compensate for it and also upgraded the steering Links to alluminium .. I installed one of these brand new out the pack it lasted about 3 turns on my truck without it even being on the ground .. the servo slammed to one side and was stuck that way ... removed the servo horn and tinted truck back on and servo was spinning by its self in one direction and wouldn’t stop ... guess that’s why they come in a 4 pack ... the these actually said emax on them not the ones pictured that are the clones

Buyer beware, these mention nothing in the add about being an Emax servo yet they have placed a label on the servo calling it an Emax servo. I did not purchase these expecting them to be the real deal, I just needed some cheap servos for a cheap project I have going. What I didn't expect was to receive servos that are branding themselves as an Emax. The logo is incorrect, these are clearly not real Emax servos and are knockoffs. IF you notice the E with the red stretched out block to the left, that is the fake way of labeling them. The real servo also has a trademark symbol in the lower right corner. I have the same authentic Emax servo and these are slightly bigger. Photos are of the knockoff. Anybody claiming in the reviews to be the real deal are being fooled.

Only used 1 of the 4 in my Axial SCX24. The servo performed very good for my application. I have ran the truck for several hours with this servo, with no issues. So far I am pleased, I do recommend this servo as a upgrade for the micro crawlers.

Great little servo’s for light balsa and foam model RC planes.

These are exactly what I need to finish another truck build they work great.

One died after like 5 min of use, rest are okay for now. Using as shift/diff lock servos in trx4, mounts took some sanding to fit, servo horn is a different size then stock, made the plastic ones it comes with work for now, kinda jittery, decent torque and speed, doesn't say it is, but definitely not water proof at all, will report back after some use.

After using the plastic-gear 9g version of these motors, I had quite a bit of trouble figuring these out. In the end, it turned out to be mainly my fault. The main issue I had, was trying to figure out how to properly use them. With my previous electronic setup, I found that when I issued movements to the servo, it would work at first, and then it would spin indefinitely (and would refuse to listen to any PWM commands). This confused me for two reasons: 1) I didn't understand why the motor was not listening to the PWM any more and 2) I didn't understand how the servo was continuously spinning in one direction (despite seeming to not be a continuous motor). Turns out the following: What was happening was that my power supply was fairly bad, and thus, when using these beefier servos, the power supply could not keep up. This, I assume was causing the servo to crash, stop reading the PWM signal. I read reviews of other Servos that advertised "continuous 360 rotation when powered off" so that tells me this motor is probably something similar. I also read another comment from someone saying that continuous motors have a tendency to continue doing the last received command. So in my case, I think what was happening was the following: The servo was given a signal to move to a position. The microchip would crash and stop reading the PWM. The microchip loses connection to the PWM and defaults to continue what it was doing before (moving). And thus, the servo doesn't stop spinning. Anywho, once I swapped out the power supply, I didn't have the same problem. I noticed someone else in the reviews mention this spinning behaviour, so hopefully, this is helpful to someone.

I gave 4 stars because these are re-brands. That being said , I cannot tell the difference from the real emax. The work extremely well, no play, and are very quiet. I will buy again