Fender Flare Rubber Seal, Fender Flare Edge Trim, Fender Flare Gasket, Fender Flares Trim for Car and Truck Wheel Wells, Bonds w/Automotive-Grade Adhesive Tape, Universal, T-Style, 60’ Length

I see some reviews stating that the adhesive isn’t good or it sticks to itself and hard to peel of if it gets stuck to itself or it’s not self explanatory. There’s enough for all 4 fenders and there will be extra for 2 fenders just in case. 1) just make sure the surface of adhesion is clean and dry 2) as you are attaching the beginning, go slow, put pressure so it sticks well, don’t try to stretch it to save extra because at the end you’ll have places where it’ll come right off, as you move along you will slowly peel of the adhesion sticker. 3) after installation if there’s small wavey areas just run your finger through the whole strip and it will flatten itself out and then cut off the excess. 4) you gotta let it settle overnight and not let it get wet for maximum adhesion.

Once I found my order at the wrong address I was good, first of the flare gasket was packaged perfect in a ziplock clear plastic bag rolled neatly. The edpm was perfect very easy to work with. Installed the gasket on both rear flares without any problems, once I was through before placing my flares back in place I went back over the gasket to make sure there wasn’t any movement . Once I finished installing my rear flares I liked the way the gasket was pressed up on the body of my Ford Superduty no gaps at all. I highly recommend if anyone is looking for replacements for their flares get these you won’t be sorry. I will update after a few weeks on how the gaskets hold up. I will add a couple photos also tomorrow.

Worked great around window trim sticks good to anything and wipes clean easily

This material is soft rubber and molded so much better than the liner that came with the flares. The adhesive seemed to be a problem in some of the reviews but we thought it was great. We cleaned the area for the strip with rubbing alcohol, applied the rubber liner and gently pulled the tape backing off. It was so easy and worked perfectly. It was also easy to straighten out during the installation of the flares. Great value because we compared ours to a friend’s expensive flares and ours looked so much better where the seal to the fender was. All in all very happy with our purchase. The installation was done in February so it worked great with the cold temps.

Used this to replace the C-channel style that came with the flares installed on a Tundra. Driving desert dirt roads the mesquite and creosote brush pulls the edging off. Also, the original edging wouldn’t stay in place around the gas filler cap. This took a little practice to get on but once it’s in place it adheres well. I’ve had no problems with it coming loose or tearing off.

Did not work on my specific vehicle, 1994 Landcruiser. The channel was was not deep enough nor wide enough to fit on the fender flares. The flare edge just rolled off the fender every time i tried to make it stick. Not gonna knock the item, just the fitment. Edit: I've measured the gap in the fender flares, which was about 4.3 mm and and the widest part of the edge banding, which was about 3 mm which would account for the reason why it did not fit well.

This is easy to install, peel and stick, and you can measure to length and cut what you need. Works really nicely at sealing off my fender flares and protection of my doors. ALOT cheaper than buying 15 feet for Orielly and Autozone

Good fit for 1st gen Tacoma

Super

Love that it has double sided tape to make it super easy to apply, makes the finished product look professional

Quality is average, i dont think it will last long

They did work on our fender flares but it was tricky to keep them in place during the install. Especially around any curves, the sharper the curve the harder it was. You need to clip the back with sissors just like if you are sewing material around a curve.

Le rendu est sympa, par contre je ne pense pas que ça durera dans le temps, ça ne collait pas très bien.