HUANUO Dual Monitor Mount up to 32 inches Screens, Taller Monitor Stand Hold 19.8lbs, Dual Monitor Arm Desk Mount Easy Adjustable with Tilt, Swivel, Rotation, VESA 75/100mm

This thing is the way to go. I have a 34' and a 48' monitor hooked up on this and the arms are doing their job. The tilt mechanism could be better. I don't love having to reset the tension on it, but that's really only for the curved 48'. The monitor hangs out a bit over the mount, so I'm overall satisfied with the stands ability to hold the monster up. This is all after over a years worth of use and going through a move. For the curious, I have the two monitors over/under. It was not that bad to configure. The little plastic bits that retain the cables can be a bit finicky, especially if you are shoving extra thick cabling through there. The cabling then has to bend with the frame, so a considerable torque may be applied to the little plastic bits, and if you pivot the stand at the monitor mount, you will likely change the length of the cabling required at that interval. Don't exepect to fit much more than a thick HDMI/DP cable and a power cord through the channels. The mount plate for the stand is really nice for providing support for the canteleiver. It gives me the warm and fuzzy on the stability of the main post.

Extremely Pleased with this product. I've used it to stack two 27" Monitors, one on top of the other AND best of all, the Mounting Stand is "Stand Alone" (NOT required to Bolt to a Table or Desk), so it's Movable if I require access to my PC or other Monitors.

Overall I really like this monitor mount. I have a couple 32" curved monitors for my gaming desk and they fit really nice. The range of motion is really large so you can get the monitors pretty much anywhere you want. All the hardware you need comes with it so you don't have to worry about that and the monitors are easy to put on. I only 1 real issue with it and that is when it comes to fine tuning the position of your monitors, that can be a bit tricky so if you're really OCD about how exactly in line your monitors are with each other, this may not be the best option for you. Also, my monitors do wiggle around a bit if I'm frustrated and slapping my desk or if I accidentally bump with my knee. They always go back to their original position but they do wiggle just a touch.

Works great. Just as expected. Pretty easy to put together.

Holds up my two monitors steady.

These monitor arms meet all my expectations. They’re sturdy, hold my monitors exactly where I want them, and haven’t sagged at all over time. The minimalist design frees up plenty of workspace underneath and doesn’t take up unnecessary room behind the desk. Installation was straightforward, and all the required hardware was included. If you’re worried about stability or losing desk space, these arms are a great choice.

Pretty easy to install! Sturdy enough that I’m comfortable with my two 32” curved monitors attached. Functionality is good, you’re able to do lots of angles. Brackets can swivel for vertical monitor placement. Good size, able to fit my large monitors comfortably. Great value for price honestly. Would order again!

Would not recommend purchasing this monitor stand. The monitor stand has been in use five days a week for just under four months. The tension for the horizontal angle rotation is not adjustable. The monitor tends to drift back to the left after the left edge of the monitor is pulled closer to you. The same drift occurs after the right edge of the monitor is pulled closer. The monitors do not remain in position after angling them toward the viewer. The slightest adjustment to the monitor results in it drifting away from the desired horizontal angle. This results in a fidgeting with both monitors for some time to position them close to where they are right. The vertical positioning works well with 15 pound monitors and holds the desired vertical position with ease after the tension is properly adjusted for the weight of the monitor. The monitor stand is clamped to the rear edge of the desk. The base of the stand that sits on the top surface of the desk is about 5 inches wide by 3.5 inches deep. The desk is 3/4-inch pressboard, so a 2x4 was cut to 6 inches long and is used to provide additional stability and strength to the desk. There is a slight amount of bounce with any bumping of the desk. The bounce lasts about 2 seconds and it is not annoying, but it is noticeable. It does not appear to be the clamp or the riser shaft that contributes to the monitor bounce. The monitor stand was straightforward to set up. The Vesa bracket is secured to the rear of the monitor first. The Vesa bracket contains slots into which the mounting plate at the end of the arm slides, so pay attention to the bracket orientation when securing it to the monitor.

Bonne qualité. Ça dégage le bureau tout en optimisant le confort.

au top, au bout de 15 jours, pas bougé. commr dit dans des commentaires, il faut prévoir un peu de place après le bureau, sinon nikel

Hat erst eine ganz billige Halterung und hab nun lange überlegt eine andere zu kaufen. Nun ist war diese hier im Angebot und hat mich überzeugt. Sie kam schnell an. Jane das Paket geöffneter und alles war sehr gut und sicher verpackt. Plan durchgeschaut und ran ans aufbauen. Ging super einfach die Anleitung war auch klar und deutlich. Viele Einstellungsmöglichkeiten um das alles anzupassen. Ich kann die Haltung klar empfehlen sie ist stabile robust und einfach zu Handhaben. Bei mir spart die auch zusätzlich viel Platz seine.

Perfect

great stand for dual monitors, mounts are easy to assemble and use. I regularly change my monitor layout and everything still works as intended