9PCS Damaged Screw Extractor Set, Hardness 63-65HRC, Upgraded Model HSS 6542, Removal Tool, Adult Gifts for Men, General Bit Set Double Ended for Damaged Broken Stripped Screws

I honestly wasn't expecting much from one of these kits as so many times, I have bought cheap tools and they haven't done the job, most times just rounding off on first use due to materials used to make them. Happy to report, this set has done the job nicely and was easy to use (instructions in the lid of the box) I was lucky enough to get a Herman Miller Aeron chair during one of our office clear-outs. One of the bolts connecting the lower links arms broke, leaving the threaded section in the hole. I used the smallest drill bit and removing tool to successfully remove the stuck part. I didn't even get the hole drilled straight due to the angle of the break but it still worked. I have another bolt on order so I can now fix the chair properly. Now to find some more stuck screws; worth the money for this one fix alone though. General words of advice for use: Drill pilot hole into stuck bolt/screw using an appropriate sized bit. Pick the right sie removal tool and drill out the pilot hole with the drill end of the tool. Turn tool around in the drill chuck (so you have the cone shaped end) . PUT DRILL IN REVERSE Push removal end of tool against the hole you drilled and slowly start to unscrew...the bit will catch and start to unscrew the stuck bolt.

Bought these after spending three day's trying various methods to release 9 rounded if hex head bolts in a hi end component. There were a few bad reviews so I was sceptical but I have to say,they turned up,I opened them,watched a two minute YouTube video put the right size extractor in my drill and literally 15 minutes later all 9 screws were out...in short what an amazing product .

I wasn't holding up much hope on previous reviews.. but honestly if you don't no how to use certain tools them even the best won't work for you .. did its job on a titanium allen bolt that had rounded off holding my front disk .. you really have to widen its position entry with the biggest bit to allow the smaller ones to have some grip ..others wise it will not work at all ..ok good luck

Does not work properly. Very poor quality, can't use them. Easy broke

Satisfactory Results

I got a bit fed up constructing some outdoor furniture with allen key bolts, there wasn't a lot of room for manouevring the allen keys so I decided to get the impact driver with some torx bits that fit in the bolt. Of course, I didn't read the instructions correctly and ended up with a left where a right should be and had to undo them again. However, I'd overtightened a couple of the bolts and couldn't get them out at all, the torx bits had worn away the hex shape. Long story short, I ordered these despite some of the negative reviews and they worked perfectly. I just followed the instructions and took it slow. I found the right fitting, the bolts came out and now I have this extra tool in my tool box just in case I can't get a screw or bolt out in the future. They've already served their purpose and saved me some DIY embarrassment for the money. If I use them again in the next 30 years then that's a nice bonus (and a sign that I haven't learned my lesson).

I was very suspicious at first. I've had many a screw rounded down to a nub in the past and usually resort to cutting a slot in the top or hammering in. A little more finesse was required when fixing my lawn mower for a rusted screw, so thought I'd give these a try. There are no instructions - but plenty of videos online. Long story short - use the chonky end - in reverse in your l eccy drill - super important - everything is in reverse. This is to wear out properly what was left of the screw head and leave a nice neat 'burred' hole for the pointy spiral end. If the same size point spiral end doesnt grab the screw (go very slowly) from the chonky hole you just made, use the next size up pointy spiral piece - I had to do this and within 10 seconds, and to my amazement, the screw was out! (I had previously spent about an hours trying WD40 and all sorts to no avail) Well worth a few quid, as I'm sure they will be used again.

Great wee set

Exactly what I expected

Habe die gesucht, weil doch öfters mal Schrauben abbrechen, die schon Ewigkeiten irgendwo drin sind. Bewertungen waren gespalten und nachdem ich ja eh aus dem Metallbau komme, entschied ich mich für die. Kann die negativen Bewertungen nicht verstehen, ja, kaputt geht immer mal was, aber man muss halt auch schauen, wie man mit etwas umgeht und arbeitet. Es sollte ja jedem klar sein, dass man hier nicht mit voller Drehzahl rein geht. Langsam muss man es schon machen, da die Schraube ja auch alt ist zb, denn sonst wäre der Kopf ja nicht abgerissen. Dann sollte es auch klappen. Im Notfall WD40 davor ran machen. Es ist alles dabei was man braucht und Bohrer hat ja eh fast jeder zu Hause. Ich bin sehr zufrieden und kann das echt nur empfehlen. Preis Leistung ist vollkommen ok, es kam sehr schön an und Qualität passt so auch.

Great, all screws are unscrewed, even those in concrete.

Je l'ai choisi notamment pour ses embouts extra fins, difficilement trouvables en commerce traditionnel. Le kit est très complet et m'a très bien dépanné pour une petite vis (2mm), je suis content de l'avoir au besoin à l'avenir, je recommande !

Ottimo